For security reasons, surveillance cameras with higher resolution have become the trend in the market. Cameras with better images usually require a higher bandwidth to maintain a stable and smooth video stream, however, there is a common phenomenon that users tend to mismatch their products with an unsuitable bandwidth due to money concern, misunderstanding about networks and the limitations in remote areas. In consequence, the large streaming volume in the videos maybe unable to fit into the confined bandwidth.

With the combination of TeleEye GN8 Series DVRs and MP4/ MP8 Series IP Cameras, videos will be automatically adjusted to seamlessly fit into any bandwidth size

TeleEye bandwidthMAX Solution 2.0

TeleEye bandwidthMAX Solution 2.0 is especially designed for the above situations! With the combination of TeleEye GN8 Series DVRs and MP4/ MP8 Series IP cameras, videos will be automatically adjusted to seamlessly fit into any bandwidth size under the newly-developed technology. By means of this intelligent solution, not only can the fluency of the video stream be guaranteed regardless of your bandwidth size, but also substantial savings can be realised as you do not need to go after a better but costlier bandwidth endlessly.

In traditional technology, the resolution of the videos is fixed regardless of the number of screens chosen. That is to say, if a total number of 16 cameras with high resolution images are viewed at the same time in the video management platform, the bandwidth may not be high enough to carry such large volume of videos, resulting in low latency in the video stream.

With TeleEye Dynamic Resolution Technology (D.R.T), the resolution of the videos will be automatically adjusted according to the chosen number of screens

TeleEye Dynamic Resolution Technology

With TeleEye Dynamic Resolution Technology (D.R.T), the resolution of the videos will be automatically adjusted according to the chosen number of screens. In which, the resolution of the videos will be decreased with the increasing number of screens chosen, and vice versa. As such, the volume of the videos can be minimised to increase bandwidth efficiency so as to allow a smoother video stream with a confined bandwidth.

Why use TeleEye bandwidthMax Solution 2.0?

  • Cost Effective

With TeleEye bandwidthMAX Solution 2.0, you can choose a network that is within your budget as our solution will intelligently integrate with your network. Thus, you don’t need to seek a faster but more expensive network without end.

  • Smoother Video Stream

TeleEye bandwidthMAX Solution 2.0 is compatible with different networks. Therefore, no matter how fast or how slow your network is, this solution provides the best-suited integration for your networks and thereby keeping the fluency of the video stream in a steady and satisfying state.

  • Support 3G/ 4G Network

TeleEye integrates the bandwidthMAX Solution with an operation on a 3G/ 4G mobile network. As such, a seamless integration of mobile communications and surveillance can still be executed under adverse environment.

  • Hacker Resistant Technology

The TeleEye Hacker Resistant Technology is incorporated in the TeleEye bandwidthMAX Solution 2.0, which shields off hackers' attack via the internet through 5 Layers of Protection: AES 265-bit encryption, specific IP access, secure protocol, pair matching architecture and isolated video network.

Share with LinkedIn Share with Twitter Share with Facebook Share with Facebook
Download PDF version

In case you missed it

COVID-19 worries boost prospects of touchless biometric systems
COVID-19 worries boost prospects of touchless biometric systems

Spread of the novel coronavirus has jolted awareness of hygiene as it relates to touching surfaces such as keypads. No longer in favour are contact-based modalities including use of personal identification numbers (PINs) and keypads, and the shift has been sudden and long-term. Both customers and manufacturers were taken by surprise by this aspect of the virus’s impact and are therefore scrambling for solutions. Immediate impact of the change includes suspension of time and attendance systems that are touch-based. Some two-factor authentication systems are being downgraded to RFID-only, abandoning the keypad and/or biometric components that contributed to higher security, but are now unacceptable because they involve touching. Touchless biometric systems in demand The trend has translated into a sharp decline in purchase of touch modality and a sharp increase in the demand for touchless systems, says Alex Zarrabi, President of Touchless Biometrics Systems (TBS). Biometrics solutions are being affected unequally, depending on whether they involve touch sensing, he says. Spread of the novel coronavirus has jolted awareness of hygiene as it relates to touching surfaces such as keypads “Users do not want to touch anything anymore,” says Zarrabi. “From our company’s experience, we see it as a huge catalyst for touchless suppliers. We have projects being accelerated for touchless demand and have closed a number of large contracts very fast. I’m sure it’s true for anyone who is supplying touchless solutions.” Biometric systems are also seeing the addition of thermal sensors to measure body temperature in addition to the other sensors driving the system. Fingerscans and hybrid face systems TBS offers 2D and 3D systems, including both fingerscans and hybrid face/iris systems to provide touchless identification at access control points. Contactless and hygienic, the 2D Eye system is a hybrid system that combines the convenience of facial technology with the higher security of iris recognition. The system recognises the face and then detects the iris from the face image and zeros in to scan the iris. The user experiences the system as any other face recognition system. The facial aspect quickens the process, and the iris scan heightens accuracy. TBS also offers the 2D Eye Thermo system that combines face, iris and temperature measurement using a thermal sensor module. TBS's 2D Eye Thermo system combines face, iris and temperature measurement using a thermal sensor module Another TBS system is a 3D Touchless Fingerscan system that provides accuracy and tolerance, anti-spoofing, and is resilient to water, oil, dust and dirt. The 2D+ Multispectral for fingerprints combines 2D sensing with “multispectral” subsurface identification, which is resilient to contaminants and can read fingerprints that are oily, wet, dry or damaged – or even through a latex glove. In addition, the 3D+ system by TBS provides frictionless, no-contact readings even for people going through the system in a queue. The system fills the market gap for consent-based true on-the-fly systems, says Zarrabi. The system captures properties of the hand and has applications in the COVID environment, he says. The higher accuracy and security ratings are suitable for critical infrastructure applications, and there is no contact; the system is fully hygienic. Integration with access control systems Integration of TBS biometrics with a variety of third-party access control systems is easy. A “middleware” subsystem is connected to the network. Readers are connected to the subsystem and also to the corporate access control system. An interface with the TBS subsystem coordinates with the access control system. For example, a thermal camera used as part of the biometric reader can override the green light of the access control system if a high temperature (suggesting COVID-19 infection, for example) is detected. The enrollment process is convenient and flexible and can occur at an enrollment station or at an administration desk. Remote enrollment can also be accomplished using images from a CCTV camera. All templates are encrypted. Remotely enrolled employees can have access to any location they need within minutes. The 3D+ system by TBS provides frictionless, no-contact readings even for people going through the system in a queue Although there are other touchless technologies available, they cannot effectively replace biometrics, says Zarrabi. For example, a centrally managed system that uses a Bluetooth signal from a smart phone could provide convenience, is “touchless,” and could suffice for some sites. However, the system only confirms the presence and “identity” of a smart phone – not the person who should be carrying it. “There has been a lot of curiosity about touchless, but this change is strong, and there is fear of a possible second wave of COVID-19 or a return in two or three years,” says Zarrabi. “We really are seeing customers seriously shifting to touchless.”

How to maximise your body temperature detection systems
How to maximise your body temperature detection systems

There are many companies jumping into selling temperature detection systems to the state, local governments, hospitals, airports and local businesses, but do they know how to drive one? Anyone can get behind a car and drive it into a wall by accident. The same can happen with a temperature detection system.  The first thing you should ask is “does my firm have a certified thermographer?”. If not, the firm are at risk of getting a low quality system that is being resold to make quick cash. Businesses that are doing this do not know how to operate it properly. Asking the right questions Secondly, you should ask whether the system is NDAA compliant. NDAA compliance means that your temperature detection equipment is protected by U.S. law. Does your system have a HSRP device (blackbody)? HSRP (Heat Source Reference Point) is a device that will allow the camera to detect the correct temperature a distance. Even if the room temperature does change throughout the day, treat it as a reference point for the camera to know the temperature at that distance. Can your system scan mutliple people at once? Can your system scan mutliple people at once? This is a bad question but often asked since most systems will say yes. For ease, everyone wants to scan many people at once, but the best practice according to FDA and CDC guidelines is to run one person at a time for best accuracy. Why? The HSRP (blackbody) device tells the camera what the correct temperature is at a given distance away from the camera. Every foot you are away from the HSRP device will be off by 0.1 degrees roughly. If you are in a room full of people, let's say 6, in view of the camera, every person that is not next to the HSRP device (5) will be given an inaccurate reading. Hence why it is so important to run the system correctly with just one person at a time. You will also need to follow the 6 feet rule. If you take that into consideration, one at a time at 6 feet apart, the device should tell you how you need to run the system. Sensitivity of thermal imaging Is your system’s sensor accurate enough? The FDA recommends an error of ±0.5°C or better. When looking for a system, make sure it is better than what they recommend. I would recommend ±0.3°C or better. Do not purchase a system over ±-.5°C degrees as you are doing yourself and your customers or employees an injustice.  Another thing to look at is how many pixels it can determine the temperature from. Some cameras can only tell the temperature of 6 points on the screen, whilst others can take a temperature reading from each pixel. Take a 384x288 camera, for example, which would be over 110,000 points of temperature taking on a single image.      Thermal cameras are very sensitive, so there are a lot of do’s and don’ts. For example, the system cannot see through glasses or hats. On the below image you can see a person with the visual camera on the right, whilst on the left side is through a thermal camera.  Both are pointing at the same area. It is clear the person on the left side is “invisible” to the thermal imaging camera. Demonstrating the sensitivity of thermal imaging If you are a company who wants to detect the temperature of customers or employees though the front door, window or a car window, the answer would be no. You need a clear line of sight without any interference to scan for temperatures. Other things you need to look out for is wind and distance away from the HSRP (blackbody) device. Air and distance away from the HSRP device will make the system less and less accurate the more space between the device. Air and distance away from the HSRP device will make the system less and less accurate Thermal imaging and COVID-19 If you have a clear line of sight, is there anything I need to know? The answer is yes. Reflective materials such as metal can interfere with your temperature readings. Reflective materials are easily picked up from the thermal side so pointing at a medal, glass or anything reflective can cause inaccuracies within the system. In the age of COVID-19, temperature detection systems are more important than ever. Organisations must get a system in place to help scan for high temperatures in order to reduce the spread of the virus.

What are the security challenges of the oil and gas market?
What are the security challenges of the oil and gas market?

Protecting the oil and gas market is key to a thriving economy. The list of security challenges for oil and gas requires the best technology solutions our industry has to offer, from physical barriers to video systems to cybersecurity. We asked this week’s Expert Panel Roundtable: what are the security challenges of the oil and gas market?