Aiphone Security access systems

Aiphone LEW-10 is a remote terminal box for wire organisation to LEF-10 masters mounted on a table or desk.

Provides a normally open dry contact closure upon call-in at a tenant station Also provides a contact to turn on external light at entrance station when calling tenant station

Allows an external device to be triggered when the intercom is called External device will be activated when the door station calls in

Aiphone GF-2F is a vandal resistant 2-module front frame for GT Series Modular Entrance Stations.

Aiphone GT-202HB is a vandal resistant 2x2-module surface mount box for GT Series entrance panel.

Aiphone GT-103HB is a vandal resistant 1x3-module surface mount box for GT Series entrance panel.

Aiphone W-DIN11 is a steel mounting bracket for DIN rail devices.

Wiring hub for AX Series using Cat-5e Two 24V DC power supply input terminals Rack mountable Controls all functionality of AX Series Two BNC composite video outputs and video switching triggers CO line transfer (requires Viking K-1900-5 programmable auto-dialer) Programmable functionality via supplied software

3 Channel Inputs Wide Frequency Response Very Low Distortion Balanced Microphone Input Phantom Power on MIC Input with Selector Balanced Telephone Paging Input VoIP Telephone Paging Input Tel and Mic Vox Sensitivity Control Independent Input Controls Bass and Treble Controls

3 Channel Inputs Wide Frequency Response Very Low Distortion Balanced Microphone Input Phantom Power on MIC Input with Selector Balanced Telephone Paging Input VoIP Telephone Paging Input Tel and Mic Vox Sensitivity Control Independent Input Controls Bass and Treble Controls

Stainless steel construction One conduit knockout on the bottom side One or two-gang mounting hole pattern Built-in rain hood

Vandal-resistant with 16-gauge stainless steel construction Flexible design can be mounted to either side of the door 1-gang hole pattern allows for easy installation

Flexible design can overhang mullion on either side of the door Wire cutouts allow for installation when there is an external conduit Clearance for Cat-5/6 cables prevents overbending

Allows desk mounting of master and/or handset station Station is propped up for easier viewing Pre-drilled mounting holes Constructed with sturdy ABS plastic Adjustable to 45° or 60° angles

Steel construction Mounts to a door mullion of a glass entry Weather resistant for outdoor use Mounts door station at 45° angle Mounts any 1-gang surface mount Aiphone Audio-only or Audio Video Door Station

Made of 12 gauge stainless steel Fully enclosed beacon/strobe light on top Emergency Lettering ADA Compliant: 4″ depth to meet ADA requirements to allow mounting higher than 27″, and proper signage and call button mounting height

Made of 12 gauge stainless steel Fully enclosed beacon/strobe light on top Assistance Lettering ADA Compliant: 4″ depth to meet ADA requirements to allow mounting higher than 27″, and proper signage and call button mounting height

Made of 12 gauge stainless steel Caged beacon/strobe light on top Assistance Lettering ADA Compliant: 4″ depth to meet ADA requirements to allow mounting higher than 27″, and proper signage and call button mounting height

UL-514-A listed electrical box included at the base Access panel at the rear base of the tower EMERGENCY signage Beacon/Strobe is always lit; flashes during emergency call-in (Requires 24V DC) Weather and vandal resistant LED for station illumination in station over-hang (requires 24V DC) Call button mounting height and signage meets ADA regulations

Emergency call from tenant station to GT-MK(B) Pull Cord Switch suitable for wet locations Normally Closed mechanically latching switch rating of 24 VDC at 500mA May be actuated by pulling on nylon cord or by pulling down the red actuator

Aiphone GT-VP is a vandal resistant panel for GT-VB camera module.

Aiphone GF-AP is a vandal resistant panel for GT-AD address module.

Aiphone GF-BP is a vandal resistant blank panel to cover open module space on GT Series entrance station.

Aiphone GF-3P is a 3-call button panel for GT-SW.

Aiphone GT-104HB is a vandal resistant 1x4-module hooded surface mount box for GT Series entrance panel.

Aiphone GF-3F is a vandal resistant 3-module front frame.

Aiphone GT-OP2 is a 2-module postal lock with frame.

Aiphone GT-OP3 is a 3-module postal lock with frame.