Senstar Indoor Security

An ultrasonic emergency notification/communication system The receiver decodes the modulated ultrasonic signal emitted by the PAT transmitter An alarm contact, auxiliary contact and LED latch each time an alarm is received They remain latched when an activated transmitter is within range The latching condition is held for 5 seconds after the transmitter is deactivated Receiving range is factory adjusted for a nominal distance of 15 m (50 ft) radius, 30 m (100 ft) diameter. This can be field adjusted if required The red alarm LED assures the user that the transmitter signal has been received and the alarm message has been sent The receiver is water-resistant and may be installed outdoors Heater for colder climates In the event of an alarm activation, the event is localised to the area monitored by the reporting receiver Flush-mounted in the wall or ceiling

An ultrasonic emergency notification/communication system The receiver decodes the modulated ultrasonic signal emitted by the PAT transmitter An alarm contact, auxiliary contact and LED latch each time an alarm is received They remain latched when an activated transmitter is within range The latching condition is held for 5 seconds after the transmitter is deactivated Receiving range is factory adjusted for a nominal distance of 15 m (50 ft) radius, 30 m (100 ft) diameter. This can be field adjusted if required The red alarm LED assures the user that the transmitter signal has been received and the alarm message has been sent The receivers are water-resistant and may be installed outdoors In the event of an alarm activation, the event is localised to the area monitored by the reporting receiver Flush-mounted in the wall or ceiling

An ultrasonic emergency notification/communication system The receiver decodes the modulated ultrasonic signal emitted by the PAT transmitter An alarm contact, auxiliary contact and LED latch each time an alarm is received They remain latched when an activated transmitter is within range The latching condition is held for 5 seconds after the transmitter is deactivated Receiving range is factory adjusted for a nominal distance of 15 m (50 ft) radius, 30 m (100 ft) diameter. This can be field adjusted if required The red alarm LED assures the user that the transmitter signal has been received and the alarm message has been sent In the event of an alarm activation, the event is localised to the area monitored by the reporting receiver Flush-mounted in the wall or ceiling

FlexPI™ is an intrusion detection sensor used to protect unsupervised building interiors. It adapts Senstar's proven microphonic cable technology to the specialized requirements of indoor security applications. FlexPI can function with a wide range of surfaces and materials when protecting structures such as walls, ceilings, roofs, stock cages, floors and pipes. It is easily integrated into most existing alarm systems.

Provides 32 output points Source voltage for outputs provided externally Up to 48 VDC, 100 mA maximum ‘on’ current 4 source voltage connections, each routed to 8 open-collector high-side contacts Configurable activation type (latching, flash mode, pulse) and timing (0.125 to 10 seconds)

Provides additional 32 input points Input activation: NO or NC Supervision types (none, single, double) and resistor values Required input activation time Noise tolerance and line drop allowance Two LEDs per input: alarm, supervision Full lightning protection: trazorbs and gas discharge devices on each input

Provides additional 32 relay output points Form-C, 1A, 30 VAC/DC non-inductive load Configurable activation type (latching, flash mode, pulse) and timing (0.125 to 10 seconds) LED indicator for each relay

Senstar F4KT0200 zone kit includes one Start Module and one End Module for installation in field splice enclosures.

19 inch rack-mount swing-out mounting plate with 35 mm DIN-rail front and back Each DIN-rail can host 2 UltraLink modules with approximately 3 inch (7.62 cm) of rail-space for other components (e.g. power supplies and/or network interface devices) Cover plate provides mechanical protection

Hosts one Gen2 Silver Network communications card (EIA-422, multi or single-mode fiber optic, or Ethernet) 8 relay output points 8 dry-contact input points Supports up to 8 expansion modules Manages up to 272 total I/O points Configurable via Silver Network™ connection or USB Comm/power fail relay Supplies power to expansion modules DIN-rail mount, 35 mm (1.38 in) “top hat” section Swing out DIN-rail with protective cover for 19 in rack Rated for indoor and outdoor use