Wiring hub for AX Series system using Cat-5e Two 24V DC power supply input terminals Rack mountable

Weather resistant Vandal resistant Inside space for cabling Mounts to flat wall surface Opening at bottom for drainage

Stainless steel surface mount box for card reader door stations Weather resistant Vandal resistant Inside space for cabling Mounts to flat wall surface Opening at bottom for drainage

A surface mount box for Aiphone's KB-DAR and KC-DAR colour video door stations Stainless steel construction Weather resistant for outdoor use

Works with existing 2-conductor wire Supplies PoE to stations LED status indicators

Provides a 24V DC output to power the strobe light in Aiphone’s wall boxes and towers The IX Series emergency stations have a secondary PoE output (passthrough) that can be used to connect to this splitter The PoE passthrough will only be usable if the IX Series station is connected and powered via a PoE+ switch

An 18-Gauge stainless steel surface mount 30° box designed for angle mounting the JO-DV, JP-DV, and JV-DV video door stations Applicable for wide or double door entrances where the door station needs to be mounted off to the side of the door, and provides a better viewing angle for the camera Weather resistant Vandal-resistant Inside space for cabling

Compatible with most Aiphone surface mount door stations Attachment holes for different standard mounting boxes, including 1- and 2-gang Mild steel front box, stainless steel back plate Conduit knockout at the base

Provides a better viewing angle for the camera Compatible with Aiphone 1-gang surface mount door stations Angles 1-gang door stations outward by 30° Can mount to either right or left of door Hinged cover for mounting door station

Made of 12 gauge stainless steel Caged beacon/strobe light on top Emergency Lettering ADA Compliant: 4″ depth to meet ADA requirements to allow mounting higher than 27″, and proper signage and call button mounting height

EMERGENCY lettering Strobe is always lit; flashes during emergency call-in (requires 24V DC) High-power speaker Camera arm with universal pipe threading Weather and vandal resistant Lightweight LED for station illumination in station over-hang (requires 24V DC) Call button mounting height and signage meet ADA regulations UL-514-A listed electrical box included at the base Access panels at the base and middle of the tower

Aiphone GT-DBP is a vandal resistant panel for GT-DB(-VN) audio module.

Aiphone GF-1P is a 1-call button panel for GT-SW.

Aiphone GF-2P is a 2-call button panel for GT-SW.

Aiphone GF-2B is a flush mount 2-module back box.

Aiphone GT-102HB is a vandal resistant 1x2-module surface mount box for GT Series entrance panel.

Aiphone GT-203HB is a vandal resistant 2x3-module surface mount box for GT Series entrance panel.

Aiphone GF-3B is a flush mount 3-module back box.

Aiphone GT-BCXB-N expanded bus control unit distributes power and data to GT Series stations for expanded systems.

Allows multiple buildings to communicate across a single, logical network Allows up to 480 Entrances, 96 Guard Stations, and 5,000 tenants

Provides selective door release capability Compatible with JP, JF, and KB Series Both normally open and normally closed output options

Video Adaptor for CCTV Camera and Audio Door Station Allows CCTV camera to be viewed on AX Series video master station Standard motion detector used to auto-activate camera Audio door station can be used for communication to camera location Relay output to trigger external device when CCTV camera is activated Video output for connection to standard CCTV monitor or recorder for full time video signal Sensor input to trigger CCTV automatically Video output allows constant viewing of CCTV camera

Page from an intercom master station through PA system Takes the place of a separate microphone for paging where there is an intercom School uses: page hallways, playground areas, cafeteria, etc. Medical facilities and/or office uses: page waiting areas, hallways, break rooms, etc.

Aiphone PC-359B is a call holding circuit board that provides latching function when call is placed from a speaker and N/O call button.

Allows two master stations to answer a single door station Combined use with RY-AC/A for external signaling

Weather resistant Vandal resistant Inside space for cabling Mounts to flat wall surface

15 V AC transformer UL Listed

Weather resistant Includes the SBX 2G/A surface mount box and PS POE splitter to power the sensor Powered from either a PoE network drop or from the LAN 2 output on an IX Series door station (requires PoE+ switch) Form C dry contact output can be connected to the trigger input of an IX Series door station Allows visitors to place a call without touching the call button on the door station Sensor is illuminated in blue while in standby and turns green when activated