CCTV Network / IP Cameras(2,333)
The FUJINON SX800 camera system marks FUJIFILM's successful entry into the surveillance systems market. FUJIFILM presents the new long-range camera module FUJINON SX800 to the surveillance systems market. With a full HD camera and an optically stabilized, 40x zoom lens from FUJINON, two high-performance components are integrated into one system. This innovation is the result of years of experience in digital cameras and a dedication to the highest optical quality. Thanks to its powerful 1/1.8" image sensor, the long focal length range of 20 mm to 800 mm and state-of-the-art image processing technology, the FUJINON SX800 is ideally suited for aerial surveillance. In modern society, the security needs of citizens are constantly increasing. Surveillance cameras with long focal lengths are not only used to address sensitive issues such as border security but are increasingly being incorporated into public infrastructure such as airports, seaports and motorways. Long range surveillance systems must cope with special challenges. For optics with long focal lengths, the smallest vibrations are sufficient to compromise the image information. Heat haze or fog in the air also impair image quality. And, a focus drive that is too slow leads to safety-relevant information loss. However, with the development of the new FUJINON SX800, FUJIFILM has found a way to minimize the impact of these challenges. Instead of developing a surveillance camera and a separate matching lens, the concept of a fully integrated system consisting of camera and lens has been realized. In addition to the high-quality zoom optics, the FUJINON SX800 has a powerful combined optical and electronic image stabilization mechanism that provides angle correction of up to ±0.22 degrees. The integrated high-speed autofocus provides a sharply focused image in less than a second, while a fog filter and heat haze reduction technology helps prevent weather interference. The system provides consistently sharp images – even of objects several kilometers away. In addition, the integrated design of the new FUJINON SX800 reduces the high adjustment effort normally required for camera installation. As of Q3 2019, the FUJINON SX800 will be available as both a mobile stand-alone device and as a system that can be integrated into a pan-tilt head.Add to Compare
System OverviewExperience 4MP full HD colour video and the simplicity of reusing existing coaxial infrastructure with HDCVI. The full-colour starlight HDCVI camera presents a high quality colour image with rich details even in total darkness conditions. It offers various fixed lens models with a multi-language OSD and HD/SD switchable output. It adopts two powerful warm white LED illuminators, covering an effective range up to 40 m (131.23 ft). The LEDs switch on automatically in darkness to capture detail-packed fullcolour images 24/7, ensuring anthentic identificaiton of objects. It is an ideal choice for applications such as schools, retail centers and parking lots. Functions Full-colour StarlightThe camera adopts F1.2 large aperture lens and 1/2.7" high performance sensor. With higher amount of absorbed light and advanced image processing algorithm, the camera presents an impressive lowlight performance with an exceptional balance between noise reduction and the blur of moving object. Warm Supplemental lightsWith two warm supplemental LED lights, the camera is able to provide a colourful and vivid image even in total dark. By default, the camera is set to smart light mode, in which the camera can automatically adjust the exposure time and light sensitivity simultaneously to avoid overexposureing of the objects in the image center. Also, the sensitivity and intensity of the LED lights can be remotely controlled by OSD menu. Broadcast-quality Audio*Audio information is used as supplementary evidence in video surveillance applications. The HDCVI camera supports audio signal transmission over coaxial cable. In addition, it adopts unique audio processing and transmission technology that best restores source audio and eliminates noise, guaranteeing the quality and effectiveness of collected audio information. 4 Signals over 1 Coaxial CableHDCVI technology supports 4 signals to be transmitted over 1 coaxial cable simultaneously, i.e. video, audio*, data and power. Dual-way data transmission allows the HDCVI camera to interact with the HCVR, such as sending control signal or triggering alarm.*Audio input is available for some models of HDCVI cameras. Long Distance TransmissionHDCVI technology guarantees long-distance and real-time transmission without any loss. It supports up to 700 m for 4MP HD video via coaxial cable, and up to 300 m via UTP cable.**Actual results verified by real-scene testing in Dahua's test laboratory. SimplicityHDCVI technology inherits the born feature of simplicity from traditional analogue surveillance system, making itself a best choice for investment protection. HDCVI system can seamlessly upgrade the traditional analogue system without replacing existing coaxial cabling. The plug and play approach enables full HD video surveillance without the hassle of configuring a network. Multiple-formatsThe camera supports multiple video formats including HDCVI, CVBS and other two common HD analogue formats in the market. The four formats can be switched over through OSD menu or by PFM820(UTC controller). This feature makes the camera to be compatible with most end users’ existing HD/SD DVRs. ProtectionThe camera's outstanding reliability is unsurpassed due to its rugged design. The camera is protected against water and dust with IP67 ranking, making it suitable for indoor or outdoor environments. With working temperature range of -40 °C to +60 °C (-40 °F to +140 °F), the camera is designed for extreme temperature environments. Supporting ±30% input voltage tolerance, this camera suits even the mostunstable power supply conditions. Its 4KV lightning rating provides protection against the camera and its structure from the effects of lightning.
VIVOTEK FD9187-HT is indoor dome network camera equipped with a full HD sensor enabling resolution of 2560 x 1944 at 30 fps. And FD9187-HT also supports standard 1920x1080 resolution at 60 frames per second. Featuring VIVOTEK SNV and WDR Pro technology, FD9187-HT is capable of capturing high quality image whether in high contrast or low light environment. The FD9187-HT offers remote focus lens for different user scenario. IR illuminators are equipped with 50 meter effective range for better night visibility. For indoor applications, PIR sensor is built-in to detect unexpected events. Employing VIVOTEK's Smart Stream III technology and H.265 codec support, the FD9187-HT reduces bandwidth up to 90%* while keeping great image quality. Additionally, powered by VIVOTEK Smart Motion Detection technology, the FE9187-HT can learn how to differentiate between the motion of people and objects, which make it enable to reduce the false alarms and have higher accuracy.
Increase safety and reduce risk on board your transit vehicles with March Networks® RideSafe MT Series IP Recorders. These all-IP units deliver highly-reliable video surveillance recording and management in a compact, rugged design that is ideal for mid-sized vehicles – like student and patient shuttles and paratransit buses. Available in 4-channel and 6-channel models, the RideSafe MT Series solution enables operators to capture everything that’s happening on the bus, inside and out. Whether you have one or a thousand vehicles, this plug-and-play recorder can operate as a standalone unit programmable through embedded software, or be remotely managed and monitored daily using March Networks Command™ for Transit video management software. Video from the recorder can also be integrated with existing CAD and AVL systems and mobile routers. Key RideSafe MT Series features include: Front panel LEDs for easy recorder diagnostics, including operational, recording and video export status Embedded Linux OS, to ensure reliable and secure video recording Real-time health monitoring, alerting operators to camera, recorder and network issues before they affect performance Vehicle metadata integration from CAD/AVL systems and accelerometers for accurate re-enactments, driver monitoring and investigations Configurable recording policies based on schedule, motion, incident/event and other user-definable variables Powerful video management software, providing the advanced tools and features needed to manage entire fleets Automated video and data extraction over WiFi or 4G networks Extended thermal range (ETR) models available
The ConteraCMR® NVR Appliance is designed to offer powerful IP recording in an affordable, compact chassis. It is equipped with an on-board 8 or 16 channel PoE switch, with a recording capacity of up to 24 channels, allowing for Plug and Play connection with Arecont Vision and ONVIF cameras or RTSP video streams. With full integration to ConteraWS® (Web Services), the NVR Appliance offers centralised user management, single sign-on convenience, mobile apps and a web client that allows for easy remote connection to your recorders. Network setup is fast and easy using ConteraWS and eliminates the need for port forwarding or DDNS. The ConteraCMR NVR Appliance runs on a secure Linux® OS and comes preloaded with ConteraVMS® Server software as a turn-key solution.
The Evolution Stainless Steel cameras, part of Oncam’s Specialist Camera Range, are unique to the 360-degree video surveillance market as they are the only ones certified for tough environments, indoor and outdoor. The 05MP and 12MP versions have been specifically designed to meet the needs of customers operating in demanding environments such as Food Processing, Industrial, Maritime and Ports and Safe City applications. The cameras’ resilient Stainless Steel 316 housing is manufactured for enhanced corrosion resistance. The IP66, IP67, IP68, IP69K, and NEMA 4X and 6P ratings make the enclosure fit for harsh environments, while its IK10+ rating makes it resistant to impacts of 40 joules. The NSF certification and HCV EU mark make the camera range unique, guaranteeing compliance with standards for commercial food equipment in both North America as well as Europe. The only 360-degree fisheye camera in a stainless steel housing, Oncam’s new and improved camera range is available for surface and pendant mount installations. A matching stainless steel arm allows for wall, corner and pole mounting. Evolution 05 Stainless Steel: EVO-05-SS2 Evolution 12 Stainless Steel: EVO-12-SS2Add to Compare
The Evolution 180 Outdoor Camera is built upon Oncam’s expertise and heritage on 360-degree technology. It is specifically designed for applications that require a dewarped panoramic view of an outdoor scene, without blind spots, from a single sensor camera. The 12MP high-resolution sensor and the built-in 3D dewarped panoramic video provides industry leading Panoramic+ views. The true day/night functionality allows images to be produced in all lighting conditions, including additional IR lighting. The camera is IP66, IP67, IP68, IP69K and IK10+ rated, making it a robust design. Its versatile enclosure enables wall and pendant mounting, while the integrated adjustable mounting allows for an angling of up to 45°. When angled, Oncam’s Angle Compensation Technology (ACT) corrects the view, straightening vertical lines in the scene.Add to Compare
System OverviewWith upgraded H.265 encoding technology, Dahua Lite series network camera has efficient video encoding capacity, which saves bandwidth and storage space. This camera adopts the latest starlight technology and displays better color image in the condition of low illumination. It supports SD card storage, dust-proof function, waterproof function and vandal-proof function, complying to the standards of IP67 and IK10 (Supported by some select models). Functions Smart CodecWith advanced scene-adaptive rate control algorithm, Dahua smart encoding technology realizes the higher encoding efficiency than H.265 and H.264, provides high-quality video, and reduces the cost of storage and transmission. WDRWith advanced Wide Dynamic Range (WDR) technology, Dahua network camera provides clear details in the environment of strong brightness contrast. The bright and dark area can get clear video even in high brightness environment or with backlight shadow. StarlightDahua Starlight technology mainly applies to the environment of low illuminance, and it can provide clear colorful video. Even in the environment of ultra-low illuminance, the technology can guarantee the good image effect. IVSWith advanced video algorithm, Dahua IVS technology supports intelligent functions, such as tripwire and intrusion. Protection (IP67, IK10, wide voltage)IP67: The camera passes a series of strict test on dust and soak. It has dust-proof function, and the enclosure can works normal after soaking in 1 m deep water for 30 minutes.IK10: The enclosure can stand the punch more than 5 times from a 5 kg hammer falling from a height of 40 cm (Impact energy is 20J).Wide voltage: The camera allows ±30% input voltage tolerance (wide voltage range), and it is widely applied to outdoor environment with instable voltage.
Hanwha Techwin’s Wisenet PNM-9000VD multi-sensor/multi-directional camera provides quality images and modular lens configuration at an affordable price. This camera supports 30fps image capture and true 120 dB WDR without compromising frame rate for each of its two 5MP sensors. Each sensor has its own Wisenet 5 chip, providing a full suite of built-in video analytics including loitering, directional detection, fog detection, tampering, motion detection and objects entering or exiting an area.
VIVOTEK’s VAST 2 is an easy to use IP video management software (VMS). To meet the real-world needs of users, it comes with exciting advancements such as easy operation on single or multiple monitors, custom layout to accommodate both corridor and panorama orientations, rapid export of multi-channel video and the acquisition of VCA analytics & cybersecurity attack events from VIVOTEK cameras and substations (such as NVRs) in a hierarchical system structure. In the new version update of VIVOTEK’s video management software VAST 2, several advanced user-centered functionalities will be unveiled. The new features include the Deep-Learning Technology Smart Search II, Cybersecurity Management Solution, and License Plate Recognition Integration. With this update, users can enjoy the intuitive interface of VAST 2 while achieving a higher level of management efficiency. Three new user-oriented benefits will be highlighted in VAST 2： Smart Search II Building on Deep-Learning Video Content Analytics, the Smart Search II of VAST 2 allows users to quickly search for specific objects and people in the specified region. While enabling People Detection feature, only people-based activities will serve as event triggers. The security operator no longer needs to search through extensive footage for critical videos, thus improving both efficiency and effectiveness. Cybersecurity Management Solution Offering the complete end-to-end cybersecurity protection, the new VAST 2 is fully integrated with VIVOTEK cameras and NVRs and becomes a powerful cybersecurity central management site. The protection includes Instant Alert Notifications, allowing users to receive notifications automatically, and the Cyber Risk Dashboard to visually identify common types of cyber-attacks. In addition, users can filter attack logs according to a range of criteria, making it quicker to find abnormal events and take necessary actions to minimize risks. License Plate Recognition Integration Now, the new VAST 2 is fully integrated with VIVOTEK’s LPR/ Automatic Number-Plate Recognition (ANPR) camera, IB9387-LPR. Users can see the live images with selected information, such as confidence level or black list status, which can in turn become a trigger source in Alarm Management, making it easy to intelligently manage license plate data.
IDIS has extended its award-winning DirectIP® camera range with the introduction of a new flagship 2MP 36x Lightmaster IR PTZ outdoor-ready camera for fast and precise pan/tilt/zoom performance.The new DC-S6283HRX Lightmaster builds on the specification of IDIS’s successful PTZ models, with a high-grade lens combined with advanced sensor technology and finely tuned, client-side image processing, allowing the capture of vivid, true colour video in extremely low light conditions. Excellent performance at long distances, with minimum motion blur, makes the DC-S6283HRX ideal for perimeters, shopping centres, stadia, outdoor spaces and public area applications.The camera benefits from IDIS’ signature true plug-and-play, one-click configuration and features 36x optical zoom, IR up to 350 metres, true wide dynamic range (WDR), digital image stabilization (DIS), a built-in heater and a vandal proof casing.“Designed for 24/7 accurate pan/tilt/zoom operation this new Lightmaster PTZ camera delivers unparalleled performance and exceptional detail when zooming. The camera is equipped with a variety of intelligent features and can move between pre-set positions and zoom in automatically in response to detected events. The result is maximum protection for a wide range of applications,” said James Min, Managing Director, IDIS Europe.The user experience is enhanced with IDIS Smart UX Controls, which is an award-winning, advanced and simple to use interface featuring intuitive slingshot and rubber-band style controls. Operators can smoothly and seamlessly follow moving objects in real-time with ground-breaking accuracy by panning images at different speeds and in different directions - literally without lifting a finger - by using a CTRL button and mouse combination.The camera uses H.264 and H.265 combined with IDIS Intelligent Codec to deliver significant bandwidth and storage savings and benefits from low Power over Ethernet (PoE) energy consumption.The risk of gaps in footage is eliminated with IDIS Smart Failover. In the event of network instability, the camera automatically records to an integral 256GB SD card and transfers data to the network video recorder (NVR) once connection is restored, which avoids the need for engineer call outs to retrieve footage.“We are listening and responding to customer demand with our new 2MP PTZ Lightmaster camera, providing an easy to deploy, low-storage and bandwidth solution for wide area coverage and perimeter detection,” said James Min, Managing Director of IDIS Europe. “It’s particularly suited to town centre and city surveillance, stadia, outdoor retail parks, manufacturing and logistics sites and high-security perimeter applications where outstanding performance and ease-of-use combined with a low total cost of ownership are becoming essential.”Add to Compare
AI series products adopt the most advanced AI technologies, including deep learning algorithms that primarily target people and vehicles, which provides higher flexibility and accuracy for end-users. This enables the Dahua AI series to offer various advanced applications such as Face Recognition, Metadata, traffic data statistics, etc. The complete lineup of Dahua AI includes network (PTZ) cameras, network video recorders, servers, and more devices. Beyond seeing the world, the power of AI allows devices to perceive the environment and understand the world in a better way. System Overview Dahua PTZ AI network camera adopts advanced CNN deep learning algorithms to support face recognition with high accuracy. The Dual 4MP Starlight Smart Capture Camera consists of panoramic camera and PTZ camera. Panoramic camera captures panoramas, and then PTZ camera takes detailed snapshots of objects and keeps tracking objects after rule violations occur. This camera possess wide monitor range and PFA algorithm that can always present a clear, focused image while zooming. Functions Dual PTZ systemPanoramic camera and Detail camera of the dual PTZ system can be adjusted horizontally and vertically. Face RecognitionOnce facial features are extracted from captured faces, they are stored in a database where they can be easily searched and compared against other images. Once a successful match is found, the system outputs the result. The Dahua Face Recognition camera supports a built-in database that stores up to 10,000 facial images, helping the camera achieve realtime face capture and comparison. Starlight TechnologyFor challenging low-light applications, Dahua's Starlight Ultra-low Light Technology offers best-in-class light sensitivity, capturing color details in low light down to 0.001 lux. The camera uses a set of optical features to balance light throughout the scene, resulting in clear images in dark environments. PFA TechnologyPFA technology has innovatively introduced new methods of judgment to ensure the accuracy and predictability of the direction of subject distance adjustment. The result is a set of advanced focusing algorithms. PFA ensures clarity of the image throughout the process of zooming and shortens focus time. The realization of PFA technology substantially improves user experience and increases product value. MetadataMetadata is feature attribute information extracted from a target object which can be used for data retrieval. There are four kinds of metadata supported by Dahua PTZ AI camera: human face, human body, motor vehicle and non-motor vehicle metadata. Facial information includes gender, age, glasses, masks, beards, etc. Human body information includes hat, top, top color, bottom, bottom color, bag, etc. Motor vehicle information includes plate color, type, vehicle color, sunshield, ornament, calling, seatbelt, smoking, annual inspection sticker, etc. Non-motor vehicle information includes type, color, top type, top color, people number, etc. Smart trackingHuman, motor vehicle, and non-motor vehicle, or their combinations can be set as objects. Once the objects selected trigger detection rules (like tripwire and intrusion), the detail camera will track them automatically. Perimeter ProtectionAutomatically filtering out false alarms caused by animals, rustling leaves, bright lights, etc. Enables system to act secondary recognition for the targets. Improving alarm accuracy. InteroperabilityThe camera conforms to the ONVIF (Open Network Video Interface Forum) specifications, ensuring interoperability between network video products regardless of manufacturer.Add to Compare
VIVOTEK ‘s new CC9381-HV is a 180-degress panoramic network camera, featuring its compact design and high-quality image capability, making it suitable for a wide array of both indoor and outdoor environments, such as boutiques, convenience stores, banks, schools and homes. Along with offering amazing 180° HFOV coverage, CC9381-HV offers up to 20 fps at 5-Megapixel resolution (30 fps at 5MP with WDR Off). This Panoramic Network Camera also incorporates other value-added features.With IR built-in 180° IR illuminators up to 15 meters, no matter day or night, light or dark, the new CC9381-HV always provides complete video security. Further, due to the SNV technology, areas of low light visibility are no longer an issue either. Equipped with WDR Pro technology, the CC9381-HV enable the camera to maintain optimal image quality and unparalleled visibility in high contrast lighting environments, as well as combined both H.265 and VIVOTEK Smart Stream III, it can reduce bandwidth and storage consumption more than 90% compared to traditional H.264 without smart streaming. In addition to its versatile coverage and features, the CC9381-HV is safeguarded by Trend Micro IoT Security to provide users with higher levels of network protection.Add to Compare
Consider your security needs met. The experts in thermal and perimeter security have packed everything you need into one affordable, easy-to-install camera. The FLIR Saros DH-390 Dome Camera includes IR and visible illuminators, plus Lepton thermal sensors to allow you to see in any condition. And with high-resolution video, you’ll never miss a thing.
Hikvision has launched a new Fisheye IP camera series (DS-2CD63X5G0) with AI. This 360˚ panoramic camera uses the deep learning technology to deliver a more accurate heat map functionality. It gives an enhanced view of its surroundings – and is especially useful in large retail applications. The cameras’ 360˚ panoramic image of the scene before it, means the user can see a wider area much more clearly. This is enhanced by independent control of a three-way infrared light, which can be separately configured to reduce the amount of ‘reflective’ wall space. This improves image quality, especially when placed in a corner location. The deep learning algorithm focuses only on human targets, improving the accuracy of the heat map functionality. This means users can see ‘hotspots’ in a space, showing areas that people visit, or pass, the most. An added layer to the heat map visualisation makes it a lot clearer than previous technologies, presenting more information in a clearer way. Despite the high quality of the images, the cameras boast extremely light bandwidth, saving storage and costs by using H265+ compression technology. They also support Multiple Expansion Modes, with up to 15 live view display modes available, designed for three different mounts. This means they can be more easily adjusted to meet the users’ exact preferences, and improve their browsing experience. Other features include: New Immervision lens (only 12MP, 1.29mm lens model) Up to 12MP resolution 120 dB WDR Up to 15m IR range Built-in microphone and speaker Smart features: 6 behaviour analyses, and 3 exception detections IK10/IP66 available. The cameras will be a useful addition to retail solutions, with heat mapping helping owners to understand customers’ psychology and identify which products attract the most attention on the shop floor. They can also be used in other large area applications, like train stations and public squares. The series will also be a boon to installers, with the ability to achieve monitoring which has no ‘dead angles’, making the solution more efficient and reducing installation costs. “We pride ourselves on continually advancing our technology and how it is implemented”, says Peter Guan, Director of Channel Sales and Marketing for Hikvision Europe. “This new Fisheye camera will provide clear flow information that will help users to make the right business decisions to make their spaces much more profitable.”Add to Compare
Easy and secure installation The Easy IP Solution makes installation easy and secure for all users. The PoE-equipped NVRs mean that the need for a separate power supply to each camera is eliminated, while the inclusion of the 4MP panoramic fisheye camera allows the entire coverage of store or office rather than having to deploy several fixed cameras. The recessed-mount dome cameras also enable installers to simply use existing downlight installations while cameras with motorised lens, and with PT (pan-tilt) and PTZ functionality eliminate the need for post-installation camera and lens direction positioning. Easy connection As well as PoE meaning that just a single Ethernet cable is required for each camera, the Easy IP Solution includes a complete range of Wi-Fi cameras and NVRs featuring auto-detection, auto-connection and easy access. At the same time, the PoE NVRs automatically allocate an IP address to each camera when it is connected, completely removing any potential delays with configuring IP address forwarding and saving time in large installations. Easy storage Featuring on-board storage on many of the cameras, Hikvision’s Easy IP Solution also offers high compression efficiency codecs to reduce the burden placed on the transmission and storage elements of the system. This is particularly significant for high-definition IP systems where bandwidth and storage costs can be a major concern - a standard H.264 camera with full HD 1080p resolution and one month of recording can result in about 1.2 TB of space consumed. The Hikvision H.264+ optimised Smart codec technology helps to reduce storage consumption by up to two-thirds, with full HD 1080p resolution for one month consuming just 462 GB. Easy and advanced viewing and video management All Hikvision Easy IP cameras support the EZVIZ Cloud – P2P service, which enables remote access from your smartphone. This means you can view the live video and recorded video files from your house, store, office or enterprise anytime and anywhere. EZVIZ also includes Intelligent Alarm support so that any intrusion or emergency events can be precisely recognised and resolved.Add to Compare
4K ResolutionLoaded with intelligent features for Behaviour Analysis and Exception Detection, the DS-2CD4A85-IZH 4k Bullet Camera combines 4K resolution with advanced video content analysis. Superior image quality of HD4096 × 2160 at 30fps supports high profile H.264 video compression. High-efficiency EXIR provides infrared at distances of up to 150 feet. Low bit rate, low latency, and region of interest-enhanced recording maximise encoding capabilities. With the camera’s highly efficient H.264+ and Region of Interest encoding, bandwidth and storage are hardly a concern. Installation is easy with an autofocus lens and a built-in wall mount bracket. Ideal for perimeter protection and critical infrastructure, the camera boasts an IP68 rating well-suited for rugged environments such as airports, seaports, power plants, and railways. Coupling this with Smart features such as line crossing, directional intrusion zones, and unattended baggage detection, the 4k Bullet Camera brings video surveillance to the next level of security.Add to Compare
Hikvision PanoVu series DS-2DP1636Z-D panoramic + PTZ cameras, with integration design, are able to capture panoramic images as well as close-up images to give consideration to both panorama and details. The panoramic images are captured by eight sensors, which could realise 360° panorama monitoring. The design of integration model and high speed PTZ offers the function of fast detail positioning over a panoramic area. Furthermore, with its advanced video analysis and multiple targets tracking algorithm, PanoVu cameras also feature a wide range of smart functions for multiple targets within the panoramic view field, including intrusion detection, line crossing detection, region entrance detection, and region exiting detection. The cameras could also output alarm signals to link the PTZ for tracking, benefitting users with great improvements in security efficiency. Camera features 1/1.9" Progressive Scan CMOS 360° view angle Up to 2 × 4096 × 1800@30fps 36X Optical Zoom Ultra-low illumination WDR 3D intelligent positioning function IP66Add to Compare
1/3 inch, Colour / Monochrome, 2 MP resolution, Digital (DSP), Megapixel, 0.01 lux, Auto Iris, 12 V DC, Motion Activated, 2.8 ~ 12, Wide Dynamic Range, 1920 x 1080, 25 fps, Inclusion DVR/ Web Server, Back Light Compensation, 1/3 ~ 1/100,000s, H.264, MJPEG, 1 RJ45 10M/100M Ethernet interface, TCP/IP, UDP,ICMP,HTTP,HTTPS,FTP,DHCP,DNS,DDNS,RTP,RTSP,RTCP, PPPoE,NTP,UPnP,SMTP,SNMP,IGMP,802.1X,QoS,IPv6,Bonjour, 5.5 W, 95 x 105 x 259, 1,200, IP66, -30 ~ +60 C (-22 ~ +140 F), 95Add to Compare
Hikvision’s range of industry-leading DarkFighter ultra-low-light CCTV cameras is expanded with six new models, including bullet, box, outdoor dome and PTZ variants. At the same time, ultra-low-light performance is also boosted with the release of the ‘DarkEye’ SLA lens, which offers a consistent ‘Super Large Aperture’ of 0.95 across the entire focal range for supreme low-light performance from close-up to maximum zoom. Quadrupling the DarkFighter network IP range All six new DarkFighter models boast industry leading low-light specifications, including large 2 MP progressive scan CMOS image sensors, full HD 1080p video at up to 60 fps, triple video streams, 3D DNR and 120dB WDR. The result is crystal-clear colour images down to as low as 0.001 Lux and B/W to 0.0001 Lux for sharp colour images in conditions that would defeat conventional low-light models. The eight-strong DarkFighter range now consists of two box cameras, two bullet cameras, two outdoor dome cameras and a pair of 23X network PTZ dome cameras, five of which come with vandal-proof housings. “DarkEye” SLA (Super Large Aperture) lens The DarkEye SLA lens HV0733D-6MP is the latest technological advance from Hikvision and significantly enhances Darkfighter performance to unrivalled levels. Featuring IR correction and up to 6 megapixel resolution, the DarkEye SLA lens is available on both DarkFighter box cameras and features a consistent aperture of f/0.95 across the entire 7-33 mm focal length range. It means that users can operate the camera at its large aperture at all times, and at any zoom setting, for maximum low-light performance. Smart solution 2.0 All DarkFighter cameras feature a host of Hikvision’s SMART technologies, which combine intelligence, efficiency, and ease-of-use into modern video surveillance. SMART technologies include face detection, intrusion detection, line-crossing detection and object counting that enables the camera to detect any progressively moving object and follow it within the camera’s area of coverage without fault. Besides, the on-board ANPR analytics further help to detect and recognize a vehicle’s license plate and send ANPR info to a Smart NVR or video management software for access management. Smart Defog and EIS (Electronic Image Stabilization) are also offered in the DarkFighter range to improve image quality in challenging conditions. Coupled with Hikvision Smart NVR and iVMS-5200 Professional video management software, the complete Smart Solution is set to accelerate the security demands in versatile vertical markets, including commercial /industrial sector, transportation, banking and much more. The DarkFighter family Newly added models: DS-2CD4026FWD (-A)(P) 2MP ultra low-light box network camera DS-2CD4A26FWD-IZ(H)(S) 2MP IR array bullet network camera DS-2CD4626FWD-IZ(H)(S) 2MP IR array vandal-proof bullet network camera DS-2CD4526FWD-IZ(H) 2MP outdoor network dome camera DS-2CD4126FWD-IZ 2MP outdoor network dome camera DS-2DF6223-AEL 2MP 23X network PTZ dome camera Existing models: DS-2CD6026FHWD-(A)2 MP ultra low-light box network camera DS-2DF8223I-AEL 2MP 23X network IR PTZ dome cameraAdd to Compare
Hikvision has released the DS-2CD2342WD-I 4MP WDR EXIR Turret Network Camera, a HiWatch video surveillance solution. The HD camera features up to 4-megapixel high resolution, 3-axis adjustment and IP67 weatherproof protection. The high-performance EXIR special rectangle IR light combines with the camera sensor for a more efficient use of light, with a 30m IR range and backlight compensation. Camera features: Up to 4 megapixel high resolution Full HD1080p video Dual stream 2.8mm/4mm/6mm fixed lens 120dB wide dynamic range 3D digital noise reduction Backlight compensation DC12V & PoE Support H.264+ High performance EXIR LED Up to 30m IR range IP67 weather-proof protection 3-axis adjustment Mobile monitoring via cloud P2P or iVMS-4500Add to Compare
Hikvision, the global leader in innovative video surveillance products and solutions, introduces a complete range of 4K surveillance products to provide a true ultra-high-definition video solution for real world security applications. The 4K Total System features Hikvision’s H.264+ Smart Codec, which reduces bandwidth and storage requirements by 50% compared to standard H.264 codecs while maximising video resolution with its optimised high-compression technology. The new 4K family includes ultra-high definition network cameras and network video recorders, all equipped with a variety of Smart functions. It is ideal for applications where clear, high-resolution images and smart surveillance of large areas are required. These include city surveillance, stadiums, parking lots, and crowd management scenarios. H.264+ Smart Codec The launch of Hikvision’s 4K Total System comes as concerns grow about the burden placed on the transmission system and storage when CCTV cameras and NVRs lacking dedicated 4K-compatible components are installed. This is not an issue with the 4K Total System, which incorporates H.264+ optimised compression to allow users to more efficiently manage ultra-high definition video footage. With features such as background-based predictive smart encoding, enhanced noise suppression, and optimised bitrate control, Hikvision’s H.264+ compression saves bandwidth resources and decreases storage requirements. The result is a complete system designed for immediate practical use, providing customers with genuinely useful end-to-end smart high-resolution security video. 4K output advantage As a further refinement, the Hikvision 4K NVRs support the HDMI 2.0 output interface, allowing users to display 4K video for monitoring applications. As a result, Hikvision’s 4K family offers users a true end-to-end 4K ultra-high-resolution solution, providing users with 4K monitoring, recording, and playback. Ultra-high definition = ultra-high quality analytics The new 4K solution, which includes 4K IP dome, bullet and box cameras along with a variety of 4K NVR models, delivers ultra-high definition (UHD) images, providing 4K resolution in real time. The high quality images also improve video analytics performance, particularly in scenes covering large areas. Limited resolution has hindered video analysis in the past, but now the additional pixels in 4K technology allow for better resolution and improved image enhancement, which in turn allow for more information to be extracted from the scene. The result is an improvement in the accuracy and quality of video analysis and better value for users. Smart features As a part of the Hikvision Smart product family, the new 4K products are equipped with smart features that put intelligence, efficiency, and ease-of-use at the heart of this state-of-the-art video surveillance range. SMART technologies include face detection, intrusion detection, line crossing detection, and smart focus. Smart tracking capability enables the cameras to detect any progressively moving object and follow it within the camera’s area of coverage, while Smart video analytics includes region enter/exit, object left behind/object removed, and more. The complete 4K total system DS-2DF6836-AEL 4K ultra-low light smart IP network PTZ dome camera DS-2DF8836I-AEL(W) 4K ultra-low light smart IP network IR PTZ dome camera DS-2CD4085F-(A)(P) 8MP Smart IP box camera DS-2CD4685F-IZ (S)(H) 8MP Smart IP IR bullet camera DS-2CD4A85F-IZ (S)(H) 8MP Smart IP IR bullet camera DS-2CD4185F-IZ 8MP Smart IP indoor dome camera DS-2CD4585F-IZ (H) 8MP Smart IP outdoor dome camera DS-9600NI-H8 4K NVR DS-7604/08/16NI-I2(/4P)(/8P) 4K NVR with 12 mega-pixel UHD support DS-7716/32NI-I4(/16P) 4K NVR with 12 mega-pixel UHD support DS-9632/64NI-I8 4K NVR with 12 mega-pixel UHD supportAdd to Compare
The launch of the BX600 HD Bullet Camera from IndigoVision creates a new, robust outdoor surveillance option with in-built IR illumination. The camera provides a high-resolution, open-standards offering and is highly effective where there is a requirement for an external camera in areas of minimal night-time ambient light. IP66 rated and ONVIF-conformant, the HD Bullet can be installed externally, without the need to be placed within an additional weather-proof housing, and can tolerate a wide range of conditions from -30°C to 50°C (-22°F to 122°F). The camera requires no additional lighting source, as it has built-in IR illumination delivering maximum image quality in low light. The easy to install HD Bullet enables customers to implement high-quality 1080p HD video while benefiting from IndigoVision’s complete solution. Users can view live and recorded video from the camera within Control Center, the user interface to IndigoVision’s Security Management Solution, SMS4™. The cameras can be located anywhere on the network and streamed to numerous clients without the need for a central server. This distributed architecture enables the solution to be easily expanded and eliminates any single point of failure. Alex Swanson, Head of Engineering, commented “The new IndigoVision HD Bullet provides us with a trusted open-standards HD camera suitable for outdoor and low-light use. Designed to work seamlessly with IndigoVision’s SMS4™, the new addition complements the existing camera range providing customers with more choice and flexibility.” The BX600 HD Bullet Camera is a further expansion to IndigoVision’s 1080p BX camera range, which includes BX400 HD Minidomes and Microdomes.Add to Compare
MOBOTIX AG recently launched the new camera platform, M15. A platform which is based on the new MOBOTIX 5 Megapixel Technology, it offers two exchangeable sensor modules and further builds on MOBOTIX‘ innovative camera platform concept. "The M15 offers the latest in MOBOTIX‘ camera system technology and follows a proud tradition that we have started over 13 years ago with the M1 and have continued with the M10 and M12," says Dr. Ralf Hinkel, founder of MOBOTIX AG. "We are confident that the M15 will be breaking ground in many ways; technically, as a product platform concept, design-wise and because it is developed in a unique combination between end-users and MOBOTIX". The M15 is naturally developed around the MOBOTIX decentralised system technology which saves costs, management and network resources for the end-user. The M15 product platform offers two exchangeable 5 Megapixel sensor modules which are exactly the same modules as for the recently launched S15. "We have developed the M15 in close cooperation with our end-users and partners. Our end-users want a dynamic platform that can change with their current and future needs, and our partners want a platform for many different applications,“ continued Dr. Hinkel. As the sensor modules can be easily exchanged by the end-user, they will always have an up-to-date camera surveillance system regardless of original mounting place and, at that time, the intended focus of that specific camera. “The end-users and our partners can today choose up to 5 completely different sensor combinations for this platform and in the future there will be even more," said Dr. Hinkel. By using 5 Megapixel sensors for the M15 camera platform, the users will gain more than four times better light sensitivity in all conditions. The new sensor technology offers a frame rate of up to 30 frames per second and the zoom capabilities are increased by 27% in colour and by more than 200% in black-and-white. "It is important to emphasize that the M15 is a Day-and-Night camera not a day/night. The difference is huge between these two concepts, the M15 sensor modules, depending on configuration, are always able to offer one day and one night image simultaneously, which is especially important in low light conditions as well as in no light," commented Dr. Hinkel. The new M15 camera platform is IP66 certified and is successfully tested at a temperature range from -30 °C to +60 °C. Following MOBOTIX established product strategy, the M15 does not need any additional housing, fans, heating etc. “The user can take our new camera platform and literally install it wherever he or she wants to. We have people using our products in very extreme environments and they will be very happy with the M15,” said Dr. Hinkel. The M15 camera platform only needs around 5 watt to be fully functional, which both saves costs and energy for the users. “The new M15 is marked with the MOBOTIX Green IP-Video logo for being exceptionally environment-friendly, which is a social conscience initiative that MOBOTIX have taken and I feel very strongly about,” concluded Dr. Ralf Hinkel. A special advantage: The M15 is fully integrated with the new revolutionary MxActivitySensor technology for intelligent motion detection that reduces false alarms and errors considerably. The M15 is available over authorised MOBOTIX distributors and partners.Add to Compare
1/3 inch, Colour / Monochrome, 2 MP resolution, Digital (DSP), Infrared, 0.01 lux, Auto Iris, Direct Drive, 12 V DC, 4, Wide Dynamic Range, 1920 x 1080, 30 fps / 25 fps, Back Light Compensation, Auto Gain Control, 1 /3 ~ 1/100,000 s, PAL, NTSC, H.264/MJPEG, 1 RJ45 10M / 100M Ethernet interface, TCP/IP,ICMP,HTTP,HTTPS,FTP,DHCP,DNS,DDNS,RTP,RTSP,RTCP, PPPoE,NTP,UPnP,SMTP,SNMP,IGMP,802.1X,QoS,IPv6,Bonjour, 5.8 W, 70 × 157 × 62, 500, IP66, -30 ~ +60 C (-22 ~ +140 F), 95, HDAdd to Compare
1/3 inch, Colour / Monochrome, 3 MP resolution, Digital (DSP), Megapixel, 0.04 lux, Auto Iris, Direct Drive, 12 V DC / 24 V AC / PoE, Motion Activated, 3 ~ 9, Surface, Wide Dynamic Range, 2048 x 1536, 30 fps / 20 fps, Inclusion DVR/ Web Server, Back Light Compensation, White Balance, 1/6 ~ 1/8000s, Zoom, H.264 (MPEG-4 Part 10/AVC), Motion JPEG, 100BASE-TX, RJ-45, IPv4, HTTP, HTTPS, SOAP, DNS, NTP, RTSP, RTCP, RTP, TCP,UDP, IGMP, ICMP, DHCP, Zeroconf, ARP, 13 W, 1710, 126 x 280 x 91, -40 ~ +55 C (-40 ~ +131 F), 0 ~ 95, HDAdd to Compare
Hikvision, the global leader in innovative video surveillance products and solutions, is set to reach new heights in extremely high contrast imaging with the launch of the LightFighter series of 2MP SMART IP cameras. Each of the seven new LightFighter cameras incorporates Hikvision’s ultra-high 140 dB WDR technology for exceptional, industry-leading visibility in brightly lit or high contrast environments. The result of this cutting-edge advance is clear, detail-rich images in lighting conditions that would defeat conventional WDR cameras. LightFighter – 7 cameras The LightFighter series consists of seven 2 megapixel cameras featuring Hikvision’s ultra-high WDR technology to overcome the pitfalls of imaging extreme backlight and high contrast scenes. The new models include a Smart IP Box camera, two outdoor Bullet cameras, two outdoor Dome cameras, and a pair of Network PTZ dome cameras with 36X zoom. All seven LightFighter cameras are also capable of rendering Full 1920 x 1080 HD images at a consistent 60 frames per second, and boast low-light capability for night time surveillance needs. 140dB WDR overcomes extreme backlighting and high contrast The key to the performance of the LightFighter cameras is the industry-leading WDR system that allows the camera to record greater scene details even where the intensity of illumination varies considerably, such as backlighting when very dark and very bright areas appear simultaneously in the field of view. Although a common feature in CCTV cameras for this reason, the 140 dB WDR in the LightFighter offers 100 times more powerful enhancement than the 120 dB WDR systems of conventional cameras. LightFighter is particularly suited to intense backlight situations, and is the ideal camera to point towards windows and entrance doors. Smart solution 2.0 The LightFighter camera range is equipped with Hikvision’s full SMART feature set, including face detection, intrusion detection, line-crossing detection, ANPR and object counting that enables the camera to detect any progressively moving object and follow it within the camera’s area of coverage without fault. Coupled with Hikvision Smart NVR and iVMS-5200 Professional video management software, the complete Smart Solution is set to accelerate the security demands in versatile vertical markets, including commercial /industrial sector, transportation, banking and much more. The LightFighter series Specifically, the DS-2CD4025FWD-(A)(P) 2MP SMART IP Box camera also features Auto Back Focus and P-Iris. The DS-2CD4A25FWD-IZ(H)(S) 2MP SMART IP Outdoor Bullet camera features a motorised varifocal lens with SMART Focus, an IR range of up to 100 meters, SMART Heating and Input/output for both alarm and audio. The DS-2CD4625FWD-IZ (H) (S) is a vandal – proof SMART IP Outdoor Bullet camera, boasting IP66 housing and an improved IR range of up to 150 meters. The LightFighter range also includes two SMART IP Outdoor Dome cameras. The DS-2CD4525FWD-IZ (H) features an IR cut filter with an auto switch, SMART Heating, and an IR range of up to 50 meters; and the DS-2CD4125FWD-IZ with a slightly reduced IR range of up to 30 meters. Rounding off the LightFighter series are two 36X Network PTZ Dome cameras, the DS-2DF6236V-AEL, and the DS-2DF8236IV-AEL. Both are equipped with a 1/3” HD CMOS sensor, capable of rendering at Full 1920 x 1080 HD, 36X Optical Zoom, SMART Tracking and SMART Detection. In addition, both models also feature IK10 Vandal–proof housings. The DS-2DF8236IV-AEL features long range IR, capable of detection and tracking at distances of up to 200 meters.Add to Compare
MOBOTIX’s AllroundDual camera balances flexibility and features continuing the trend of modular system design. The MOBOTIX M16 AllroundDual features exchangeable image sensors for day, night and thermal use along with flash memory, microphone, speaker, PIR and optional feature modules. Housed within a weatherproof (IP66) chassis along with a comprehensive set of built-in cyber security controls, the camera offers powerful new application and integration options for both system integrators and end customers. The M16 also proves that standards and innovation can truly co-exist as the MOBOTIX video surveillance camera that brings together the MxPEG video codec specifically developed for security applications and the H.264 industry standard within an ONVIF-ready camera system. For added flexibility, the built-in RTSP/Multicast capability allows simultaneous streaming of MxPEG, M-JPEG and H.264 video to multiple clients without performance loss. Benefiting from an upgraded processor and software, the M16 delivers the highest frame rate of any MOBOTIX camera along with intelligent 3D motion detection and more capacity for on-board software applications. The M16, in common with all MOBOTIX models, benefits from regular software updates to ensure reliability while adding additional feature enhancements that make the M16 one of the most intelligent yet flexible camera systems on the market.Add to Compare
1/3 inch, Colour / Monochrome, 480 resolution, Megapixel, 0.03 lux, CS mount, 12 V DC / 24 V AC, 12, Back Light Compensation, JPEG, UDP, TCP, SOAP, DHCP, Zeroconf, 6 W, 85 x 67 x 53, 530, -10 ~ +50, 20 ~ 80Add to Compare
1/3 inch, Colour / Monochrome, 1920 x 1080 resolution, Megapixel, 0.02 lux, Auto Iris, 12 V DC / 24 V AC, PoE, 3 ~ 9, Wide Dynamic Range, 30, White Balance, 1/6 ~ 1/8000 sec, 69, IPv4, HTTP, HTTPS, SOAP, DNS, NTP, RTSP, RTCP, RTP, 6 W, 470, 120 x 67 x 53, -10 ~ +50, 20 ~ 80, HDAdd to Compare
1/3 inch, Colour / Monochrome, 2 MP resolution, Megapixel, 0.04 lux, Auto Iris, 12 V DC, 1920 x 1080, 30 IPS, White Balance, 1/6 ~ 1/8000 sec, NTSC / PAL, Zoom, H.264, Motion JPEG, IPv4, HTTP, HTTPS, SOAP, DNS, NTP, RTSP, RTCP, RTP, TCP,UDP, IGMP, ICMP, DHCP, Zeroconf, ARP, 6W, 560, 156 x 69 x 64, -10 ~ +50, 20 ~ 80, HDAdd to Compare
1/3 inch, Colour / Monochrome, 2 MP resolution, Digital (DSP), Megapixel, 0.04 lux, Auto Iris, Direct Drive, 12 V DC / 24 V AC / PoE, Motion Activated, 3 ~ 9, Surface, Wide Dynamic Range, 1920 x 1080, 30 fps, Inclusion DVR/ Web Server, Back Light Compensation, White Balance, 1/6 ~ 1/8000s, Zoom, H.264 (MPEG-4 Part 10/AVC), Motion JPEG, 100BASE-TX, RJ-45, IPv4, HTTP, HTTPS, SOAP, DNS, NTP, RTSP, RTCP, RTP, TCP,UDP, IGMP, ICMP, DHCP, Zeroconf, ARP, 13 W, 1710, 126 x 280 x 91, IP66, IK10 , -40 ~ +55 C (-40 ~ +131 F), 0 ~ 95, HDAdd to Compare
Hikvision’s SMART IP camera ranges are being boosted with four newly added 6 megapixel Ultra HD camera series that provides a total resolution of 3072 x 2048 at full frame rate to deliver spectacular images. With this immense of view, one 6MP camera covers the area of several conventional cameras. Like the DS-2CD4065F-(A) SMART IP box camera that launched last year, all four of the new models feature industry-leading specifications and are powered by Hikvision’s signature SMART technologies. These include SMART Codec, SMART Focus, SMART IR, SMART Facial Recognition, SMART Line Crossing Detection, SMART Voice Recognition and SMART License Plate recognition, which helps to deliver a unique smart experience of unparalleled image quality and customer convenience. Full frame rate in real-time Unlike the majority of Full HD cameras that can only transmit a 2 megapixel image (1920 x 1080) at their full frame rate, all the Hikvision 6MP SMART IP cameras are capable of transmitting a full 3072 x 2048 6 megapixel image, even at full frame rate. This capability will be especially suited to applications requiring highly detailed surveillance, capturing the fine detail of license plates, clothing and faces to help law enforcement or monitoring cash handling areas, for instance. The 6MP resolution combined with user-defined ROIs and SMART detection technologies also means a single camera from this new family could monitor an entire area that would previously have required a raft of low resolution units. At the same time, the ultra-low light capability and Smart IR built into the new range adjusts IR strength to maximise image quality in less than ideal lighting conditions. Finally, all four cameras are capable of streaming three simultaneous and independent HD video streams. Smart solution 2.0 The 6MP IP cameras deliver a complete Smart Solution when combined with Hikvision Smart NVR and comprehensive video management software. With front-end cameras providing Smart Detection, backend device for Smart Playback/backup and video management software for Smart management, Hikvision Smart range well combines intelligence, efficiency, and ease-of-use into modern video surveillance, and provides maximum security efficiency for operation and post-event investigation etc. Expanding customer choice “As the global CCTV market continues to move towards HD as the de facto standard, Hikvision is leading the way towards an HD+ future with the 6MP SMART IP family,” says Keen Yao, International Marketing Director at Hikvision. “Their enhanced imaging capabilities demonstrate the cutting-edge that our investment in R&D brings to customers worldwide.” About the models: The DS-2CD4A65F-IZ (H) SMART IP Outdoor Bullet camera’s key features include a motorised VF lens with SMART focus combined with an IR range of up to 50 metres. The DS-2CD4565F-IZ (H) SMART IP Outdoor Dome camera is a cousin to the DS-2CD4165F-IZ, featuring all the industry leading specifications of the DS-2CD4165F-IZ while being adapted for use in outdoor environments.Add to Compare
1/3 inch, Colour / Monochrome, 4 MP resolution, Digital (DSP), Megapixel, 0.01Lux @(F1.2,AGC ON ), 0.0 28 Lux @(F 2.0 ,AGC ON), 0 Lux with IR lux, Auto Iris, Direct Drive, 12 V DC, PoE , Motion Activated, High Speed, Wide Dynamic Range, 2688 x 1520, 30 fps / 25 fps, Back Light Compensation, Auto Gain Control, 1/3 ~ 1/10,000s, H.264, M-JPEG, H.264+, 1 RJ45 10M/100M Ethernet interface, TCP/IP, UDP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTSP, RTCP, PPPoE, NTP, UPnP, SMTP, SNMP, IGMP, 802.1X, QoS, IPv6, Bonjour, I3: Max. 6W ; I5: Max. 7.5W ; I8: Max. 10.5W, 300 x 86 x 85, 1200, IP67, -30 ~ +60 C (-22 ~ +140 F), 0 ~ 95Add to Compare
1/3 inch, Colour / Monochrome, 2 MP resolution, Digital (DSP), Megapixel, 0.0 1 Lux @(F1.2,AGC ON) , 0 Lux with IR 0.0 28 Lux @(F 2.0 ,AGC ON) , 0 Lux with IR lux, Auto Iris, Direct Drive, 12 V DC, PoE , Motion Activated, High Speed, Wide Dynamic Range, 1920 × 1080, 30 fps / 25 fps, Back Light Compensation, Auto Gain Control, 1/3 s ~ 1/100,000 s, H.264, M-JPEG, 1 RJ45 10M/100M Ethernet interface, TCP/IP,ICMP,HTTP,HTTPS,FTP,DHCP,DNS,DDNS,RTP,RTSP,RT CP, PPPoE,NTP, UPnP, SMTP,SNMP, IGMP, 802.1 X ,QoS,I P v6 ,Bonjour, 4.5 W, 72 x 90 x 131, 400, -30 ~ +60 C (-22 ~ +140 F), 0 ~ 95, HDAdd to Compare
VIVOTEK, a global IP surveillance provider introduced a new stereo network camera for retail solutions, the SC8131. The SC8131 delivers 3 key benefits for the retail market, including: Accurate Traffic Analysis: Uniquely designed with a dual-lens, the SC8131 mimics the eyes of human beings. Thanks to its 3D Depth Technology with up to 98% accuracy rate, the camera can distinguish individuals or groups, adult or children, and filter out carts, and strollers. Furthermore, it obtains bi-directional counting on a definable flow and tracking a moving path, avoiding double counting caused by u-turns. Improve Staff Management: When retailers recruit security staff or part-time employees to manually count traffic they tend to produce a less than satisfactory result. With VIVOTEK’s SC8131, these valuable human resources now can be managed more efficiently while producing far higher levels of accuracy. Optimize Operating Decisions: VIVOTEK is committed to helping retailers think ahead and maximise their ROI. The SC8131 enhances business intelligence via VIVOTEK’s central management software, VAST, which produces dedicated counting reports. These real-time reports can be exported by schedule or for areas in a line chart, bar graph or pie chart and directly exported into Snapshot. And all the data can also be exported to Microsoft Excel for analysis. Finally, VAST provides a seamless counting function, which secures counting data all the time, even during unexpected network or power disruption. With VIVOTEK, information vital to your business will always be on hand.Add to Compare
The S14 FlexMount from MOBOTIX, the world’s first flexible double hemispheric camera, is now available. The camera, which is available in both mono (S14M) and dual (S14D) versions, features miniature lens units and offers a wide range of application opportunities. For instance, the S14D can be equipped with two hemispheric lens units with integrated microphone that are connected to the main housing via cables. This makes it possible to fully secure two rooms located next to or on top of one another with just one single S14. The slim design of the module units, which are available in white and black, permit an extremely discreet installation. Two rooms secured with one single camera The S14 FlexMount offers the option to set up two hemispheric lens units simultaneously in order to completely cover two adjacent rooms with just one single S14D. When installed in a certain way, the S14D can also see around corners or secure indoor and outdoor areas at the same time. The two sensors allow the S14 to generate two distortion-corrected, high-resolution 180° panorama images, each with a resolution of 3.1 megapixels. All other MOBOTIX lenses, from super-wide angle to tele lens, will be available in the near future as day or night versions.The S14 is the world's first hemispheric day-and-night camera. When both modules with black-and-white and colour sensors are mounted directly next to each other and cover the same area, the camera automatically chooses the best available mode depending on the lighting conditions. This provides for excellent colours in daylight as well as superb light sensitivity in dark environments. Panning and zooming into the image is done purely electronically. The user is provided with detailed views and other image sections without any mechanical movement, meaning that there is no wear-and-tear to the camera and no maintenance is required. Weatherproof, discreet and energy efficient Both module units and the separate housing with the latest dual camera board are weatherproof in accordance with IP65 and operate in a temperature range of -30°C to +60°C (-22°F to +140°F). The flat housing, including flash memory with up to 64 GB and all external connectors (Ethernet, MiniUSB, MxBus), can be installed discreetly and with optimal protection behind a wall or ceiling panel so that only the lens units in their ultra-compact protective housing are visible. Power is supplied very cost effective via a network cable (PoE). At less than five watt-hours, the energy consumption is extremely low. Wide range of application opportunities The camera's technical features and very discreet mounting open up a whole range of application opportunities. In L-shaped rooms, for example, the two sensor modules can be positioned at the corner in correct angles to each other, therefore capturing the entire room without any blind spots. Therefore, the S14 is particularly well-suited for use in hotels, banks and retail stores where the highest levels of security and discretion are required. The S14 can also demonstrate its strengths at security gates and in offices. MOBOTIX also offers the appropriate installation accessories for mounting the sensor module on thicker walls. Using several extension pieces (each approx. 40 mm), longer "tunnel holes" through a wall can also be bridged. MOBOTIX software included free of charge As usual with all MOBOTIX products, the complete software for configuration and operation of the camera is integrated directly into the camera. Additionally, professional video management software can be downloaded from the website free of charge.Add to Compare
MOBOTIX has launched a new series of thermal camera products, equipped with a new type of thermal sensing technology to realise automatic events, based on absolute temperatures within -40°C to +550°C (or -40°F to +1022°F). This new technology is perfect to generate automatic alarms, defined by temperature limits or temperature ranges, which is vital to detect potential fire or heat sources. At the same time, MOBOTIX provides a free software update to upgrade existing thermal cameras with thermal spot metering in the image centre. Within the available temperature range of -40°C to +550°C (or -40°F to +1022°F) and a thermal sensitivity of 0.05°C (NETD=50mK), different temperature conditions can be easily defined within the new TR (Thermal Radiometry) window or over the whole sensor image with a typical accuracy of ±10°C. Up to 20 multiple temperature events can be defined at the same time. Spot metering, which measures temperature related to 4 pixels at the image centre, is also improved in the new thermal TR products with a typical accuracy of ±10°C. These new releases will help to prevent bigger damages in industrial and commercial premises, at manufacturing and logistic sites, recycling facilities, forests, etc. MOBOTIX Thermal Radiometry (TR) is available in its popular M15, and as a sensor module in the S15 dual camera system. Furthermore, TR is also available as S15 PT-mount sensor head. Both S15 thermal modules can be set up as dual thermal system for most flexible usage or as the perfect combination of thermal and optical sensor technology to ensure the most reliable detection results and visual verification at the same time.Add to Compare
This amazing and intelligent solution has enriched Smart features, and consists of many innovative, industry-leading IP products. The Smart Solution 2.0 solution is also the ideal choice for various vertical applications. Enriched smart features Smart IP Solution 2.0 includes Smart features such as object counting, region entering, region leaving, object removing, object leaving, target cropping stream and ANPR (customisation required). Industry-leading IP products New Hikvision IP cameras have been incorporated into this solution, including the DarkFighter series, LightFighter series, 6MP Ultra HD series, 4K series, and new 3MP WDR series, with industry-leading product performance. Versatile solutions Smart IPC and Smart NVRs with Smart features are the perfect solution for small and mid-sized applications. For mid-sized to large-sized applications, iVMS-5200 Professional software further improves the system's effectiveness with Smart features and analytics. Tailored to vertical applications As an all-in-one Smart platform to manage cameras, NVRs, alarms, access control and decoders, the Smart Solution 2.0 is loaded, with Smart features and analytics such as people counting, heating mapping, LPR, and more. This makes it highly adaptable to verticals’ special requirements and can be used in retail, banking, hotel and industrial applications, among others.Add to Compare
1/3 inch, Colour / Monochrome, 2 MP resolution, Digital (DSP), Megapixel, 0.01 lux, Auto Iris, Direct Drive, PoE, Motion Activated, 3 ~ 9, Surface, Wide Dynamic Range, 1920 x 1080, 30 fps, Inclusion DVR/ Web Server, Auto Gain Control, White Balance, 1/6 ~ 1/8,000s, Zoom, H.264 (MPEG-4 Part 10/AVC), Motion JPEG, RJ-45 connector, 100BASE-TX, IPv4, HTTP, HTTPS, SOAP, DNS, NTP, RTSP, RTCP, RTP, TCP, UDP, IGMP, ICMP, DHCP, Zeroconf, ARP, 9 W, 285 x 131 x 97, 1290, IP66, IK10, -30 ~ +60 C (-22 ~ +140 F), 0 ~ 95, HDAdd to Compare
Browse CCTV Network / IP Cameras
IP camera products updated recently
Back in the 1960s a lead engineer working in conjunction with the United States Navy for Lockheed’s Skunk Works team coined the acronym KISS, which translated to the design principle ‘keep it simple stupid’. The KISS principle embraces the concept of simplicity, stating that most systems work best if they are kept simple rather than geared up to be more complicated. When it comes to physical security systems, this concept can also play a key element in its overall success. Secure work environments For years the tug of war in the security industry has pitted the need for a secure environment against the desire for technology that is convenient for users. However, finding a happy medium between the two has often seemed elusive. I believe you can design and have operational convenience at the same time as achieving high security" Jeff Spivey, a security consultant and the CEO of Security Risk Management, has this to say about it, “If there is an understanding of the security-related risks and their separate and/or collective impact on the organisation’s bottom line business goals, a resolution can be reached.” Jeff also does not think that convenience and high security have to be opposing each other. He says, “I believe you can design and have operational convenience at the same time as achieving high security.” Importance of secure access control The premise is that for organisations and spaces to be truly secure, they must be difficult to access. So, by its very nature, access control is designed to be restrictive, allowing only authorised staff and visitors to access a facility or other secured areas inside. This immediately puts convenience at odds with security. Most people will tolerate the restrictive nature of a controlled entrance using badge, card or biometric because they understand the need for security. When that technology gets in the way of staff traversing freely throughout the facility during the course of a business day, or hindering potential visitors or vendors from a positive experience entering the building, they become less tolerant, which often leads to negative feedback to the security staff. Enhancing corporate security Security consultants like Spivey and security directors all stress that understanding the threats and risk levels of an organisation will most likely dictate its physical security infrastructure and approach. All the technology in the world is useless if it is not embraced by those who are expected to use it and it doesn’t fit the culture of the organisation. Once employees and customers are educated about what security really is, they understand that they're not losing convenience, they're gaining freedom to move safely from point A to point B. Converged data and information shape new access options Migration of physical access control systems to a more network-centric platform is a game-changer for security technologies The migration of physical access control systems to a more network-centric platform has been a game-changer for emerging security technology options. The expansion of the Internet of Things (IoT), Near-Field Communication devices powered by Bluetooth technology, and the explosion of converged information systems and identity management tools that are now driving access control are making it easier than ever before for employees and visitors to apply for clearance, permissions and credentials. Wireless and proximity readers Advancements in high-performance wireless and proximity readers have enhanced the user’s access experience when presenting credentials at an entry and expediting movement throughout a facility. A user is now able to access a secured office from street-level without ever touching a key or card. Using a Bluetooth-enabled smartphone or triggering a facial recognition technology, they enter the building through a security revolving door or turnstile. A total building automation approach adds extra convenience, as well as seamless security, when access technology is integrated into other systems like elevator controls. A total building automation approach adds extra convenience and seamless security How to Meet Security Concerns at the Entry While security managers are charged with providing their facilities the maximum level of security possible, there is always the human element to consider. But does the effort to make people comfortable with their security system ecosystem come at a cost? Does all this convenience and the drive to deliver a positive security experience reduce an organisation’s overall levels of security? And if so, how can we continue to deliver the same positive experience including speed of entry – while improving risk mitigation and threat prevention? Door entrances, barriers Users can slip through the door or turnstile barriers while they are still open after a credentialed individual has gone through Let’s examine some of the various types of entrances being used at most facilities and the security properties of each. With some entrance types, there is the possibility for security to fall short of its intended goals in a way that can’t be addressed by access control technology alone. In particular, with many types of doors and barriers, tailgating is possible: users can slip through the door or turnstile barriers while they are still open after a credentialed individual has gone through. To address this, many organisations hire security officers to supervise the entry. While this can help to reduce tailgating, it has been demonstrated that officers are not immune to social engineering and can often be “talked into” letting an unauthorised person into a facility. Deploying video cameras, sensors Some organisations have deployed video surveillance cameras or sensors to help identify tailgaters after the fact or a door left open for longer than rules allow. This approach is not uncommon where facilities have attempted to optimise throughput and maintain a positive experience for staff and visitors. Security staff monitoring the video feeds can alert management so that action can be taken – but this is at best a reactive solution. It does not keep the unauthorised persons from entering, and so is not a totally secure solution. Optical turnstiles, speedgates Security staff should carefully evaluate its facility’s needs and consider the technology that is built into the door itself Security staff should carefully evaluate its facility’s needs and consider the technology that is built into the door itself. Not all security entrances work the same way. And, there will always be a balance between security and convenience – the more secure the entry, the less convenient it is for your personnel and visitors to enter your facility. For example, it takes more time to provide 2-factor authentication and enter through a mantrap portal than to provide only one credential and enter through an optical turnstile or speedgate. Perimeter protection So, it is an important first step to determine what is right at every entrance point within and around the perimeter. Remember that convenience does not equate to throughput. Convenience is the ease and speed of entry experienced by each individual crossing that threshold, while throughput relates to the speed at which many individuals can gain access to the facility. A more convenient entry makes a better first impression on visitors and is good for overall employee morale. Throughput is more functional; employees need to get logged in to begin their workday (and often to clock in to get paid), and they quickly become frustrated and dissatisfied when waiting in a long line to enter or exit the premises. Considering form and function when designing a security entrance can ensure that those requiring both high-security and convenience are appeased.
Imagine a home surveillance camera monitoring an elderly parent and anticipating potential concerns while respecting their privacy. Imagine another camera predicting a home burglary based on suspicious behaviors, allowing time to notify the homeowner who can in turn notify the police before the event occurs—or an entire network of cameras working together to keep an eye on neighborhood safety. Artificial Intelligence vision chips A new gen of AI vision chips are pushing advanced capabilities such as behavior analysis and higher-level security There's a new generation of artificial intelligence (AI) vision chips that are pushing advanced capabilities such as behavior analysis and higher-level security to the edge (directly on devices) for a customisable user experience—one that rivals the abilities of the consumer electronics devices we use every day. Once considered nothing more than “the eyes” of a security system, home monitoring cameras of 2020 will leverage AI-vision processors for high-performance computer vision at low power consumption and affordable cost—at the edge—for greater privacy and ease of use as well as to enable behavior analysis for predictive and preemptive monitoring. Advanced home monitoring cameras With this shift, camera makers and home monitoring service providers alike will be able to develop new edge-based use cases for home monitoring and enable consumers to customise devices to meet their individual needs. The result will be increased user engagement with home monitoring devices—mirroring that of cellphones and smart watches and creating an overlap between the home monitoring and consumer electronics markets. A quick step back reminds us that accomplishing these goals would have been cost prohibitive just a couple of years ago. Face recognition, behavior analysis, intelligent analytics, and decision-making at this level were extremely expensive to perform in the cloud. Additionally, the lag time associated with sending data to faraway servers for decoding and then processing made it impossible to achieve real-time results. Cloud-based home security devices The constraints of cloud processing certainly have not held the industry back, however. Home monitoring, a market just seven years young, has become a ubiquitous category of home security and home monitoring devices. Consumers can choose to install a single camera or doorbell that sends alerts to their phone, a family of devices and a monthly manufacturer’s plan, or a high-end professional monitoring solution. While the majority of these devices do indeed rely on the cloud for processing, camera makers have been pushing for edge-based processing since around 2016. For them, the benefit has always been clear: the opportunity to perform intelligent analytics processing in real-time on the device. But until now, the balance between computer vision performance and power consumption was lacking and camera companies weren’t able to make the leap. So instead, they have focused on improving designs and the cloud-centric model has prevailed. Hybrid security systems Even with improvements, false alerts result in unnecessary notifications and video recording Even with improvements, false alerts (like tree branches swaying in the wind or cats walking past a front door) result in unnecessary notifications and video recording— cameras remain active which, in the case of battery powered cameras, means using up valuable battery life. Hybrid models do exist. Typically, they provide rudimentary motion detection on the camera itself and then send video to the cloud for decoding and analysis to suppress false alerts. Hybrids provide higher-level results for things like people and cars, but their approach comes at a cost for both the consumer and the manufacturer. Advanced cloud analytics Advanced cloud analytics are more expensive than newly possible edge-based alternatives, and consumers have to pay for subscriptions. In addition, because of processing delays and other issues, things like rain or lighting changes (or even bugs on the camera) can still trigger unnecessary alerts. And the more alerts a user receives, the more they tend to ignore them—there are simply too many. In fact, it is estimated that users only pay attention to 5% of their notifications. This means that when a package is stolen or a car is burglarised, users often miss the real-time notification—only to find out about the incident after the fact. All of this will soon change with AI-based behavior analysis, predictive security, and real-time meaningful alerts. Predictive monitoring while safeguarding user privacy These days, consumers are putting more emphasis on privacy and have legitimate concerns about being recorded while in their homes. Soon, with AI advancements at the chip level, families will be able to select user apps that provide monitoring without the need to stream video to a company server, or they’ll have access to apps that record activity but obscure faces. Devices will have the ability to only send alerts according to specific criteria. If, for example, an elderly parent being monitored seems particularly unsteady one day or seems especially inactive, an application could alert the responsible family member and suggest that they check in. By analysing the elderly parent’s behavior, the application could also predict a potential fall and trigger an audio alert for the person and also the family. AI-based behavior analysis Ability to analyse massive amounts of data locally and identify trends is a key advantage of AI at the edge The ability to analyse massive amounts of data locally and identify trends or perform searches is a key advantage of AI at the edge, for both individuals and neighborhoods. For example, an individual might be curious as to what animal is wreaking havoc in their backyard every night. In this case, they could download a “small animal detector” app to their camera which would trigger an alert when a critter enters their yard. The animal could be scared off via an alarm and—armed with video proof—animal control would have useful data for setting a trap. Edge cameras A newly emerging category of “neighborhood watch” applications is already connecting neighbors for significantly improved monitoring and safety. As edge cameras become more commonplace, this category will become increasingly effective. The idea is that if, for example, one neighbor captures a package thief, and then the entire network of neighbors will receive a notification and a synopsis video showing the theft. Or if, say, there is a rash of car break-ins and one neighbor captures video of a red sedan casing their home around the time of a recent incident, an AI vision-based camera could be queried for helpful information: Residential monitoring and security The camera could be asked for a summary of the dates and times that it has recorded that particular red car. A case could be made if incident times match those of the vehicle’s recent appearances in the neighborhood. Even better, if that particular red car was to reappear and seems (by AI behavior analysis) to be suspicious, alerts could be sent proactively to networked residents and police could be notified immediately. Home monitoring in 2020 will bring positive change for users when it comes to monitoring and security, but it will also bring some fun. Consumers will, for example, be able to download apps that do things like monitor pet activity. They might query their device for a summary of their pet’s “unusual activity” and then use those clips to create cute, shareable videos. Who doesn’t love a video of a dog dragging a toilet paper roll around the house? AI at the Edge for home access control Home access control via biometrics is one of many new edge-based use cases that will bring convenience to home monitoring Home access control via biometrics is one of many new edge-based use cases that will bring convenience to home monitoring, and it’s an application that is expected to take off soon. With smart biometrics, cameras will be able to recognise residents and then unlock their smart front door locks automatically if desired, eliminating the need for keys. And if, for example, an unauthorised person tries to trick the system by presenting a photograph of a registered family member’s face, the camera could use “3D liveness detection” to spot the fake and deny access. With these and other advances, professional monitoring service providers will have the opportunity to bring a new generation of access control panels to market. Leveraging computer vision and deep neural networks Ultimately, what camera makers strive for is customer engagement and customer loyalty. These new use cases—thanks to AI at the edge—will make home monitoring devices more useful and more engaging to consumers. Leveraging computer vision and deep neural networks, new cameras will be able to filter out and block false alerts, predict incidents, and send real-time notifications only when there is something that the consumer is truly interested in seeing. AI and computer vision at the edge will enable a new generation of cameras that provide not only a higher level of security but that will fundamentally change the way consumers rely on and interact with their home monitoring devices.
Protecting against fire and security risks is an essential aspect of life for people and across all sectors. However, there is an increasing expectation and demand on fire and security providers, in areas such as education. The securitisation of our world paired with the rapid speed of communication and news updates means that young people especially have the potential to be more aware of potential dangers and threats to their own safety and the safety of those around them. Education institutions are large and sometimes sprawling sites that present considerable fire and security challenges. From kindergarten to university Each education site brings distinct challenges, with differing facilities and specialties, as well as the need to maintain the capacity of students, teachers and lecturers to study, learn and teach at the high level expected.Each education site brings distinct challenges, with differing facilities and specialties While some schools and universities are based in urban areas with a mix of heritage and high rise buildings, others are sprawled across green open spaces. Some of these sites have specialised sporting facilities, while others may be focused on engineering or scientific study, with costly technical equipment. Kindergartens and primary schools have their own unique requirements. Parents expect the highest safety standards, while schools require safety in addition to efficient facilities management. The demographic of these institutions is predominantly young children, who are often unaware of or only just learning about fire safety and personal safety. This creates a huge vulnerability and an added onus on teachers to keep their students safe. Facial recognition at West Academy of Beijing In response to this need, Chubb China upgraded the closed-circuit television (CCTV) system for Western Academy of Beijing (WAB) focusing on elevating video content analytic features, including maximised CCTV monitoring, automatic police calling, and a smart search solution. Complementing this, a facial recognition system capable of finding the exact location of a student on campus within 30 seconds was added, aided by real-time remote gate operation. This integrated and advanced system resulted won the "High Quality Educational Technology Suppliers for School" award for the WAB project at the 2019 BEED Asia Future Oriented Construction of Universities and Schools Seminar. This award recognises outstanding solution design and project execution. Parents expect the highest safety standards, while schools require safety in addition to efficient facilities management Awareness remains important at university As students graduate from kindergarten, primary school, junior and senior school, they become more aware of fire safety, relevant dangers and how to protect themselves. Unfortunately, external dangers remain. There are particularly high stakes for university campus facilities managers The safety of students in a university environment is also critical. It is often the first time young people live away from their family home and have the independence of adulthood. For this reason, there are particularly high stakes for university campus facilities managers. In the eventuality of a fire, students could be at great risk and, beyond the immediacy of physical harm, this can have serious ramifications for the reputation of an educational institution. Integrated solutions Integrated solutions must be nimble and adapted to a range of site types including campus residences, recreational areas, open spaces and lecture theatres. Chubb Sicli recently identified and overcame these challenges through the installation of a full suite of fire safety and security equipment and services at Webster University Geneva. Established in Switzerland in 1978, Webster University Geneva is an accredited American university campus that offers programs in English to students interested in undergraduate or graduate-level education. Located in the Commune of Bellevue, just a few kilometres from Geneva's central station, the campus of Webster University Geneva includes five buildings in a park-style atmosphere. Full fire and security audit Chubb Sicli provided Webster’s fire extinguisher maintenance for over 25 years. This business relationship led to a full fire and security audit that identified the need for updates to the university’s security installation. The initial audit showed several improvements to the university’s security profile were needed.The challenge was to create and provide an effective and interconnected fire and security solution The challenge was to create and provide an effective and interconnected fire and security solution, enhancing the security of the student population and its ever-evolving needs. This included complete fire detection and intruder alarms for all five buildings, upgrades to existing CCTV systems, new video surveillance equipment and an automated fire extinguishing system in the kitchen areas. In addition to this integrated system solution, Webster University required access control for all main entrances, with the requirement that all documentation to be made available in English, because Webster is an American company. Customised solution Chubb Sicli’s quality, capability, and security expertise provided a customised solution for the unique educational establishment. Not only was the solution both tailored and integrated, the approach and planning were based on audit, fire extinguisher and emergency light maintenance, fire detection, intrusion detection, access control, video surveillance and Fire Detection. Through dedicated and integrated fire safety support, Chubb provides students and families peace of mind and security. From the moment a young child enters the education system, Chubb’s diligent and effective surveillance and fire safety systems work to prevent and protect, offering a new kind of ‘end-to-end’ service for education systems around the world.
The security behind financial securityDownload
Nine ways to make your retail security system work harderDownload
Financial institutions require future-ready physical security technologiesDownload
Dahua Technology’s Safe City Solution chosen by the local government to make Brienon-sur-Armançon safer
- Dahua Technology secures Astana’s BI-City Tokyo residential complex with Smart Residential Solution
- Dahua Technology’s Safe City Solution chosen by the local government to make Brienon-sur-Armançon safer
- Prescott Valley’s Ocean Blue Car Wash installs 3xLOGIC video surveillance system for enhanced security
- Matrix Comsec provides central monitoring solutions and secures Nashik railway station during Kumbh Mela