MOBOTIX Intruder Detectors & Detection Systems (3)
Radar wave-based detection of moving objects, even if there is no difference in temperature between these and the environment Ideal supplement to PIR sensors that only react to infrared radiation Detection of all kinds of movements, plus the option to filter out radial movements (only sends MxMessage for approaching/distancing objects, for instance) Pre-defined profiles of approaching/distancing/movements for optimal detection of human movements Completely concealed installation behind wood, plastic or drywall is possible (with reduced detection range)Add to Compare
The Passive Infra-Red Sensor (PIR) has been a common part of a security installer’s kit bag for many years; yet these sensors are normally just used to detect movement, which is somewhat limiting. MOBOTIX MxMultiSense offers an innovative alternative. Available in indoor and weatherproof outdoor models, the new 4-way sensor connected via MxBus can be used in combination with a MOBOTIX camera to read specific sensor values. Additional sensor featuresAlong with movement detection, each MxMultiSense can also measure noise, temperature and brightness. Various sensors readings can be used individually or combined as desired with event logic to perform intelligent functions. This can include traditional motion detection for alarm activation, along with more advanced automation functions such as turning on or off lights triggered on the Lux level or external heaters based on temperature. With a low power consumption of 0.1 Watt and compatibility with a wide range of signal receiving devices via MxBus, MxMultiSense makes it possible to cost-effectively extend camera installations and monitor areas which cannot be covered by cameras.Add to Compare
The MxMultiSense MxBus device from MOBOTIX is an affordable accessory to increase security inside and outside of buildings. The device detects and reports movements and noise levels and measures the temperature and illumination level – environmental information, which can then be used for individually configurable functions, such as activation of a signal output at 5 °C or 100 Lx. All four sensors can be combined as desired (via event logic). The compact MxMultiSense has a very low power consumption of 0.1 Watt. With the same form factor as an S15 sensor module and is therefore compatible with all sensor module mounts available for wall or ceiling installation.Add to Compare
Browse Intruder Detectors & Detection Systems
- PIR Detectors
- Glassbreak Detectors
- Infra Red Beams
- Shock Sensor
- Pet Tolerance
Intruder detector products updated recently
Today’s organisations face numerous diverse threats to their people, places and property, sometimes simultaneously. Security leaders now know all too well how a pandemic can cripple a company’s ability to produce goods and services, or force production facilities to shut down, disrupting business continuity. For example, a category three hurricane barreling towards the Gulf of Mexico could disable the supplier’s facilities, disrupt the supply chain and put unexpected pressure on an unprepared local power grid. Delivering timely critical information Tracking such risk is hard enough, but managing it is even more difficult. A swift response depends on delivering the right information to the right people, at the right time. And, it’s not as easy as it sounds. Indeed, 61 percent of large enterprises say critical information came too late for them, in order to mitigate the impact of a crisis, according to Aberdeen Research (Aberdeen Strategy & Research). These challenges are accelerating the hype around Artificial Intelligence (AI) These challenges are accelerating the hype around Artificial Intelligence (AI). The technology promises to help us discover new insights, predict the future and take over tasks that are now handled by humans. Maybe even cure cancer. Accelerating the hype around AI But is AI really living up to all this hype? Can it really help security professionals mitigate risk? After all, there’s a serious need for technology to provide fast answers to even faster-moving issues, given the proliferation of data and the speed at which chaos can impact operations. Risk managers face three major obstacles to ensuring business continuity and minimising disruptions. These include: Data fatigue - Simply put, there’s too much data for human analysts to process in a timely manner. By 2025, the infosphere is expected to produce millions of words per day. At that pace, you’d need an army of analysts to monitor, summarise and correlate the information to your impacted locations, before you can communicate instructions. It’s a herculean task, made even more difficult, when we consider that 30 percent of this global datasphere is expected to be consumed in real time, according to IDC. Relevance and impact - Monitoring the flood of information is simply the first hurdle. Understanding its impact is the second. When a heat dome is predicted to cover the entire U.S. Pacific Northwest, risk managers must understand the specifics. Will it be more or less hot near their facilities? Do they know what steps local utilities are taking to protect the power grid? Such questions can’t be answered by a single system. Communication - Once you know which facilities are impacted and what actions to take, you need to let your employees know. If the event is urgent, an active shooter or an earthquake, do you have a fast, effective way to reach these employees? It’s not as simple as broadcasting a company-wide alert. The real question is, do you have the ability to pinpoint the location of your employees and not just those working on various floor in the office, but also those who are working from home? How AI and ML cut through the noise Although Artificial Intelligence can help us automate simple tasks, such as alert us to breaking news, it requires several Machine Learning systems to deliver actionable risk intelligence. Machine Learning is a branch of AI that uses algorithms to find hidden insights in data, without being programmed where to look or what to conclude. More than 90 percent of risk intelligence problems use supervised learning, a Machine Learning approach defined by its use of labelled datasets. The benefit of supervised learning is that it layers several pre-vetted datasets, in order to deliver context-driven AI The benefit of supervised learning is that it layers several pre-vetted datasets, in order to deliver context-driven AI. Reading the sources, it can determine the category, time and location, and cluster this information into a single event. As a result, it can correlate verified events to the location of the people and assets, and notify in real time. It’s faster, more customised and more accurate than simple Artificial Intelligence, based on a single source of data. Real-world actionable risk intelligence How does this work in the real world? One telecommunications company uses AI and ML to protect a mobile workforce, dispersed across several regions. An AI-powered risk intelligence solution provides their decision makers with real-time visibility into the security of facilities, logistics and personnel movements. Machine Learning filters out the noise of irrelevant critical event data, allowing their security teams to focus only on information specific to a defined area of interest. As a result, they’re able to make informed, proactive decisions and rapidly alert employees who are on the move. Four must-have AI capabilities To gain real actionable risk intelligence, an AI solution should support four key capabilities: A focus on sourcing quality over quantity. There are tens of thousands of sources that provide information about emerging threats - news coverage, weather services, social media, FBI intelligence and so much more. Select feeds that are trusted, relevant and pertinent to your operations. Swift delivery of relevant intelligence. To reduce the mean-time-to-recovery (MTTR), risk managers need an accurate understanding of what’s happening. Consider the different contextual meanings of the phrases ‘a flood of people in the park’ and ‘the park is at risk due to a flood’. Machine Learning continuously increases the speed of data analysis and improves interpretation. Ability to cross-reference external events with internal data. As it scans different data sources, an AI engine can help you fine-tune your understanding of what’s happening and where. It will pick up contextual clues and map them to your facilities automatically, so you know immediately what your response should be. Ready-to-go communications. Long before a threat emerges, you can create and store distribution, and message templates, as well as test your critical communications system. Handling these tasks well in advance means you can launch an alert at a moment’s notice. The ability to minimise disruptions and ensure business continuity depends on speed, relevance and usability. AI and ML aren’t simply hype. Instead, they’re vital tools that make it possible for security professionals to cut through the noise faster and protect their people, places and property.
The impact of the COVID-19 pandemic has accentuated our digital dependency, on a global scale. Data centres have become even more critical to modern society. The processing and storage of information underpin the economy, characterised by a consistent increase in the volume of data and applications, and reliance upon the internet and IT services. Data centres classed as CNI As such, they are now classed as Critical National Infrastructure (CNI) and sit under the protection of the National Cyber Security Centre (NCSC), and the Centre for the Protection of National Infrastructure (CPNI). As land continues to surge in value, data centre operators are often limited for choice, on where they place their sites and are increasingly forced to consider developed areas, close to other infrastructures, such as housing or industrial sites. Complex security needs One misconception when it comes to data centres is that physical security is straightforward One misconception when it comes to data centres is that physical security is straightforward. However, in practice, things are far more complex. On top of protecting the external perimeter, thought must also be given to factors, such as access control, hostile vehicle mitigation (HVM), protecting power infrastructure, as well as standby generators and localising security devices to operate independently of the main data centre. Face value How a site looks is more important than you may think. Specify security that appears too hostile risks blatantly advertising that you’re protecting a valuable target, ironically making it more interesting to opportunistic intruders. The heightened security that we recommend to clients for these types of sites, include 4 m high-security fences, coils of razor wire, CCTV, and floodlighting. When used together in an integrated approach, it’s easy to see how they make the site appear hostile against its surroundings. However, it must appear secure enough to give the client peace of mind that the site is adequately protected. Getting the balance right is crucial. So, how do you balance security, acoustics and aesthetics harmoniously? Security comes first These are essential facilities and as a result, they require appropriate security investment. Cutting corners leads to a greater long-term expense and increases the likelihood of highly disruptive attacks. Checkpoints Fortunately, guidance is available through independent accreditations and certifications, such as the Loss Prevention Certification Board’s (LPCB) LPS 1175 ratings, the PAS 68 HVM rating, CPNI approval, and the police initiative - Secured by Design (SBD). Thorough technical evaluation and quality audit These bodies employ thorough technical evaluation work and rigorous quality audit processes to ensure products deliver proven levels of protection. With untested security measures, you will not know whether a product works until an attack occurs. Specifying products accredited by established bodies removes this concern. High maintenance Simply installing security measures and hoping for the best will not guarantee 24/7 protection. Just as you would keep computer software and hardware updated, to provide the best level of protection for the data, physical security also needs to be well-maintained, in order to ensure it is providing optimum performance. Importance of testing physical security parameters Inspecting the fence line may seem obvious and straightforward, but it needs to be done regularly. From our experience, this is something that is frequently overlooked. The research we conducted revealed that 63% of companies never test their physical security. They should check the perimeter on both sides and look for any attempted breaches. Foliage, weather conditions or topography changes can also affect security integrity. Companies should also check all fixtures and fittings, looking for damage and corrosion, and clear any litter and debris away. Accessibility When considering access control, speed gates offer an excellent solution for data centres. How quickly a gate can open and close is essential, especially when access to the site is restricted. The consequences of access control equipment failing can be extremely serious, far over a minor irritation or inconvenience. Vehicle and pedestrian barriers, especially if automated, require special attention to maintain effective security and efficiency. Volume control Data centres don’t generally make the best neighbours. The noise created from their 24-hour operation can be considerable. HVAC systems, event-triggered security and fire alarms, HV substations, and vehicle traffic can quickly become unbearable for residents. Secure and soundproof perimeter As well as having excellent noise-reducing properties, timber is also a robust material for security fencing So, how do you create a secure and soundproof perimeter? Fortunately, through LPS 1175 certification and CPNI approval, it is possible to combine high-security performance and up to 28dB of noise reduction capabilities. As well as having excellent noise-reducing properties, timber is also a robust material for security fencing. Seamlessly locking thick timber boards create a flat face, making climbing difficult and the solid boards prevent lines of sight into the facility. For extra protection, steel mesh can either be added to one side of the fence or sandwiched between the timber boards, making it extremely difficult to break through. A fair façade A high-security timber fence can be both, aesthetically pleasing and disguise its security credentials. Its pleasant natural façade provides a foil to the stern steel bars and mesh, often seen with other high-security solutions. Of course, it’s still important that fencing serves its primary purposes, so make sure you refer to certifications, to establish a product’s security and acoustic performance. Better protected The value of data cannot be overstated. A breach can have severe consequences for public safety and the economy, leading to serious national security implications. Countering varied security threats Data centres are faced with an incredibly diverse range of threats, including activism, sabotage, trespass, and terrorism on a daily basis. It’s no wonder the government has taken an active role in assisting with their protection through the medium of the CPNI and NCSC. By working with government bodies such as the CPNI and certification boards like the LPCB, specifiers can access a vault of useful knowledge and advice. This will guide them to effective and quality products that are appropriate for their specific site in question, ensuring it’s kept safe and secure.
Enclosures containing electronics, communications or cabling infrastructure offer a simple attack point for cyber breaches and an opportunity for a physical attack on the hardware. Yet, many of these assets are housed within enclosures that provide minimal security features to offer a deterrent to any would-be attacker. This has always just been a pet hate. Walking down the high street of a town anywhere in the United Kingdom, you can often see open street communication cabinets. You can actually look directly inside at the equipment. And if I was a bad guy, I could quite easily just put my foot into their enclosure and quite quickly take out their infrastructure. Charged service for enclosures This seems crazy when a US$ 2 magnetic contact on a door can quickly tell you whether your enclosure is open or shut, and can be vital in keeping your network alive. Moreover, the operators of these systems, whether it is telecoms or internet providers, are providing a charged service to their customers, so they should really be protecting their enclosures. Why has that security level not been so readily taken into the outside world, into the unprotected environment? More sobering, if you contrast this security approach to the approach taken in the data centre world, an environment that already has multiple stringent security protocols in place, you get a very different picture. For instance, security devices can capture snapshots of anyone who opens a cabinet door in a data room, so it is recorded who has opened that door. While that is just one simple example, it begs the question. Why has that security level not been so readily taken into the outside world, into the unprotected environment? In my mind, a lot of it boils down simply to education. Network connection, easy point of cyber attacks Our preconceived idea about cyber security is some big corporation being knocked out or held to ransom by, again in our mind, someone sitting at a laptop, probably with their hood up over their head, typing away in the darkness, attacking us through the internet. But how the would-be criminal is going to come at us is just like in sport. They attack at the weakest point. Networks can be deployed in the outside world in many ways, such as cameras monitoring the highways. That means those locations will have a network connection. And that can be a point of attack in a non-secure outside world. Enclosures can be broken into by attackers Many people think, ‘That is okay because I’m going to take that ethernet device that my cameras are connected to and I’m going to put it inside an enclosure.’ However, what people do not realize is that the only thing that the enclosure is doing is protecting the ethernet device from Mother Nature. Because, without proper security, those enclosures can be broken into pretty easily. Many of them are just a single key that is not in any way coded to the device. Twofold cyber security People need to realise that cyber security is twofold. It can be carried out by hacking the network or physically breaking Therein lays the problem. People need to realise that cyber security is twofold. It can be carried out by hacking the network or physically breaking into the weakest physical point. And so, a simple boot through the open door of an enclosure can vandalise the devices inside and take down a small or large part of a network. And by definition, this meets the criteria for a cyber-attack. So, how do we go about tackling this problem? Well, security is a reaction marketplace. And for enclosures, there’s not, at present, a plethora of solutions out there for to counter these types of attacks. It can be challenging to find what you’re looking for through a quick Google search compared to searching for more traditional security protection measures. Deploying smart sensors and detectors But, under Vanderbilt and ComNet, we are currently taking our knowledge and experience from system installation and compiling it together. We’re bringing different products from different parts of our business to make a true solution. For instance, we have sensors for enclosures that detect anything from gas or smoke to open doors, detectors that will tell you if someone is trying to smash open your enclosure with a sledgehammer, or that someone is trying to lift your enclosure off of its mount. More importantly, as is not really a one-size-fits-all solution, we have developed a menu structure available that allows customers to pick and choose the ones that will best fit their own requirements.
The manufacturer-independent IT solutions firm, SySS GmbH has tested and certified the security of the MOBOTIX 7 intelligent video platform and MOBOTIX Mx6 security cameras. As a result, the renowned institute for penetration tests in Germany has confirmed the best possible cyber security of MOBOTIX products and solutions. SySS GmbH testing certified During the tests, hardware and software components are subjected to simulated hacker attacks in several scenarios. These correspond to the current cyber-attacks, which have recently led to data tapping and data hijacking worldwide. The testers of SySS GmbH are familiar with the recent attack methods on IT systems and research how to prevent the intrusion into digital infrastructures. With this exclusive know-how, SySS GmbH tests IT landscapes and looks for weaknesses and security vulnerabilities. MOBOTIX 7 intelligent video platform and Mx6 cameras We only offer our customers video systems and solutions that provide the best possible protection" “The renewal of the SySS certificate for our MOBOTIX 7 platform and our Mx6 camera series confirms our continuous acting. We only offer our customers video systems and solutions that provide the best possible protection - not only for people, facilities, goods, grounds, or buildings but also for the data that our recordings collect,” emphasizes MOBOTIX’s Chief Technology Officer (CTO), Hartmut Sprave. With MOBOTIX, customers can be sure that they will continue to be protected against cyber threats. The MOBOTIX 7 platform and the Mx6 security camera series from MOBOTIX are among the market-renowned systems in IoT camera applications. ONVIF and H.264 compliant They are appreciated worldwide for their robustness, durability, and energy-efficient solutions. Despite the decentralised approach, the system is ONVIF and H.264 compliant. Furthermore, all MOBOTIX products and solutions are integrated into the comprehensive cyber security strategy, whose overall measures are bundled in the MOBOTIX Cactus Concept. Hartmut Sprave concludes, “From the high-end video system to our software and app offering in the comprehensive video management solutions, we are the reliable, convincing and cyber-secure solution provider in the video surveillance market, with the stringent high demand for best quality.”
With MOBOTIX HUB, MOBOTIX AG is expanding its offering in the field of video management software. From a few local cameras to thousands of devices distributed worldwide, the company from Langmeil in Rhineland-Palatinate now offers complete system solutions for almost any requirement of specific vertical markets. For example, the open video management platform MOBOTIX HUB can integrate all ONVIF-enabled MOBOTIX video systems and more than 10,000 additional cameras and devices at a wide variety of locations worldwide. In addition, the highly performant platform maps the constantly growing variety of intelligent video analysis tools and other functions. While the cameras continue to form the basis of each system, the use of supplementary event and analysis software based on deep learning and artificial intelligence opens up versatile protection, optimisation, and security functions. Workflow, business, and production processes can thus be made more efficient and secure. MOBOTIX ManagementCenter MOBOTIX HUB provides the user with a central node and control point that connects all network components. All video and security systems are easy to control, giving the user the best possible overview. MOBOTIX thus offers its customers - in addition to the MOBOTIX CLOUD and the MOBOTIX ManagementCenter - three video management solutions covering the complete range of requirements, from small applications to the largest, highly security-oriented multi-site projects. In addition, customers using only MOVE cameras can use MOBOTIX MOVE NVR as an integrated storage and management solution. With MOBOTIX HUB, we have expanded our bandwidth in such a way that we can serve any company" "We want to offer our customers and partners product solutions that are a perfect fit," emphasises MOBOTIX CTO Hartmut Sprave. "With MOBOTIX HUB, we have expanded our bandwidth in such a way that we can serve any company of our focused vertical market. All requirements for the function and performance of video security systems can now be supported with proprietary MOBOTIX video management software products." Video management platform MOBOTIX HUB is an open video management platform (VMP) for companies of all types and sizes. It integrates all elements of modern video systems - even in highly complex structures and across any number of locations. The platform combines security and analytics cameras, access control systems, security equipment, environmental sensors, software and hardware interfaces to industrial equipment, and much more in a common control and user interface - centralised, transparent, and user-friendly. Through the intelligent use of collected data, MOBOTIX HUB helps to effectively protect people and property and analyse behaviour. It also provides users with new information that can be used to optimise business processes and workflows. Video Wall MOBOTIX provides five different levels of the MOBOTIX HUB: from the free L1 system for small, local applications with up to eight cameras to the MOBOTIX HUB L5, which is suitable for extremely large, enormously security-oriented applications - with an unlimited number of cameras and devices installed at a wide variety of locations worldwide. Flexible access to the video system can be provided via the Mobile, Web, or Desk Client. The Video Wall, accessible for the two most potent levels L4 and L5, provides the user with a completely transparent overview in an all-round control centre. The video management platform can continuously connect additional video equipment and new techniques Every solution is different. Every industry and every company has its requirements. MOBOTIX HUB will grow with future hardware and software developments in the video security market. As an open system with ONVIF compatibility, the video management platform can continuously connect additional video equipment and new techniques. It can independently assign alarms and trigger any functions. MOBOTIX HUB is almost arbitrary expandable. With three product updates per year, MOBOTIX ensures that the system is always up-to-date. Cybersecurity "Video technology has evolved beyond pure security requirements. Providing data for optimisation, marketing, and integration into other systems is an absolute necessity today," says Thomas Lausten, CEO of MOBOTIX AG. "MOBOTIX HUB is an important part of this, and we will continue to support integration with other VMS partners. We are a solution provider. Our goal is to always guarantee our customers the best fitting solution, according to their current and future requirements," said Lausten. Like all MOBOTIX solutions, MOBOTIX HUB is designed to enable secure end-to-end communication to protect data and the entire network. Cybersecurity measures are constantly being developed to be dynamically armed against cyberattacks permanently. The MOBOTIX HUB VMP software offers a whole matrix of security mechanisms. Tiered administrator and user permissions enforced on the server-side, combined with the use of strict IT security procedures, make MOBOTIX HUB the first choice for security-sensitive companies and organisations.
Once upon a time, providers had end-to-end control when deploying a physical security platform, which is not the case anymore when we consider the modernisation to IP. When considering the move to IP physical security, the provider needs to ensure the customer has a robust PoE backbone to connect the IP security device back to the application. Network readiness requirements have complicated IP security deployments, making it challenging for current providers while opening the door to new competitors. Competition is increasing Network providers see the move to IP as an opportunity to expand their wallet share. As the trusted advisors to IT teams, network providers leverage their position to win over the physical security business. As the time, cost, and complexity increases to move a customer to IP; providers need to expand their offering, considering the decline in endpoint revenue margins (the "race to the bottom"). Unfortunately, PoE networks are becoming increasingly complex as IoT endpoints are continually introduced to the network. Before the IP/IoT deployment can occur, the network provider (now your competition as well) will have the opportunity to edge you out and offer an IP/IoT solution with the network. The traditional approach is outdated They have standardised this cookie-cutter solution that may work for some, but not for all While we accept that we are collectively relying on our networks to support an increasing number of devices and applications, many have not considered the local area network's evolution. Organisations no longer only connect data terminals and printers to the network - they connect all manner of intelligent devices, including Wi-Fi access points, cameras, phones, access control, lighting, intercoms, and more. Many traditionalists will recommend the rip-and-replace of existing infrastructure while layering all IoT devices on the same network. They have standardised this cookie-cutter solution that may work for some, but not for all. What if there was a better way? Create the best outcome for you and your customer Let's start by thinking about the customer's desired outcome. The customer wants new capabilities within an acceptable ROI. Given the complications surrounding COVID-19, these organisations may require solutions very quickly to operate safely and within governmental guidelines. However, these organisations first need to establish a LAN framework without high costs, disruption to business, or complexity. They do not want to compromise network security or their business. They do not want network requirements to account for the majority of their budget as there is no ROI in infrastructure. The infrastructure supports the ROI gained from the devices and applications it enables. How do we provide a network solution that addresses both the customer and the provider's needs? Customers need a network that: Eliminates competitive pressures, giving providers end-to-end control over the network and the entire digital transformation experience. Shorten sales and deployment cycles to simplify network readiness and reduce the budget allocation towards infrastructure. Focus on device and application implementation and adoption to improve the customer's ROI. Build a physically separate PoE backbone for IP/IoT applications to maximise network security and performance while simplifying ongoing management. Eliminate the dependency on other providers. Advice from Albert Einstein We cannot solve a problem using the same kind of thinking we used when we created it" To help achieve these outcomes, I encourage you to accept some advice from Albert Einstein. Einstein once said, "The only thing that interferes with my learning is my education." Sometimes we are unwilling to accept new ideas because of preconceived notions about how things "ought to be done." We must embrace innovation and challenge our best practices that are based on past education. Einstein also said, "We cannot solve a problem using the same kind of thinking we used when we created it." Sometimes we must challenge ourselves to think differently by using innovations to create better outcomes for our businesses and customers. Consider this for a second: are you focused on the problem rather than finding a unique alternative solution? Einstein defined insanity as "doing the same thing over and over and expecting different results." Your customers are all unique with different digital transformation challenges and objectives. The cookie-cutter, rip-and-replace method has not worked for all. If it did, every organization would have all the IP and IoT solutions they need. It's time to consider a fresh new approach that may challenge your education. Don't let our education get in the way of your learning! Looking to innovation and modern solutions The idea of The Modern LAN, introduced by Frost & Sullivan, aims to present a paradigm shift in LAN design for IP and the IoT. The whitepaper, available for free using the link above, offers an enhancement to traditional LAN design to address IP and IoT devices' specific needs. Today, we connect more than just data terminals, and we must design our networks accordingly. Instead of starting with the network, Modern LAN design suggests starting with the endpoint requirements and building a network to address these considerations. One of the foundations of Modern LAN design is to consider all networking innovations available. NVT Phybridge PoE innovations allow you to leverage different cable types, including coax, single-pair UTP, and multi-pair UTP cabling, to enable IoT devices at much greater distances than traditional switches. Aligned with Modern LAN design, you can transform the existing network into a robust and secure PoE backbone instead of removing and replacing the reliable infrastructure. PoE switch solutions PoE switch solutions leverage different core technology that vary in capability and effectiveness I know what you may be thinking: Am I compromising on network performance by leveraging these innovations? The answer is: it depends on the technology. PoE switch solutions leverage different core technology (Homeplug, VDSL, ADSL, Ethernet, etc.) that vary in capability and effectiveness. For more than 15 years, NVT Phybridge has been a global pioneer in long-reach PoE technology. We were the first company to develop a switch that delivered Ethernet and PoE over a single pair of UTP wire with up to 1,200ft (365m) reach, which is four times the reach of standard switches. We have spent the last 15 years surprising the industry with our capabilities and satisfying customers with our technology. Performance is paramount We understand that innovation is met with scrutiny and skepticism. We also know that some companies make claims that they cannot back up, which can sometimes shed a negative light on an entire industry or product category. However, our enterprise-grade networking solutions have helped thousands of customers modernise to the next generation of intelligent devices without high costs, complexity, or disruption to their business. For example, our CLEER24 switch is a 24-port Ethernet over Coax innovation that delivers Ethernet and PoE+ over a single coax cable with up to 6,000ft (1,830m) reach, which is 18-times the reach of a standard switch. Transform network readiness requirements into an opportunity to grow your business! Be a thought leader, leverage Modern LAN design, and introduce NVT Phybridge PoE innovations to your customers. It's time to change the conversation around LAN design and improve the outcome for you and your customers.
Related white papers
Market Report: Cannabis at a glance
Optimise your business with analytics and AI
Protecting dormitory residents and assetsDownload
Protecting Critical Infrastructure through facial recognitionDownload
12 questions to ask your access control providerDownload
Providing frictionless cloud Video Storage as a Service (VSaaS)Download
- Vanderbilt provides SPC system to enhance access control system at the Maritime Culture Center
- TiOC 2.0: Customisable security alarm system made possible by Dahua
- HAECO automates its tool control for aircraft maintenance, repair and overhaul (MRO) services with Xerafy's RFID solution
- Ajax protects the Vernadsky Research Base with fire detectors and fire alarm systems