Intruder Warning Devices(224)
Perimeter protection is one of the most effective ways to prevent an intruder. A more secure system is one that alerts the user of the presence of an intruder, before they can break into the property. It’s a simple idea, but fitting an external detector comes with challenges. Install the brand-new XDL12TT-AM and provide up to 12m premium and robust pet-friendly external detection. Consisting of two independent Passive Infrared (PIR) sensors and one microwave sensor, the Tri-Technology (TT) of the XDL12TT-AM utilises Tri-Signal Detection Logic to identify the presence of an intruder. This provides reliable and stable external detection as all three sensors must be activated sequentially in quick succession to create an alarm. This enhances the detector’s immunity to environmental disturbances and limits the risk of false alarms. With Dual-Vision Pet Immune Technology, each PIR sensor of the XDL12TT-AM has its own dedicated volumetric field of view. The top PIR detects outwards and up, while the bottom PIR detects outwards and down, without overlapping. This setup, alongside Tri-Signal Detection Logic, delivers highly secure sequential detection and increases its tolerance to pet immunity. So, should any large dogs or cats stray into the coverage plane, it would only be picked up by the bottom PIR and the microwave sensors and therefore an alarm condition would not be activated. However, the lens coverage of the PIRs are angled so that any human will be detected walking through both PIR coverage planes. Therefore, as all three sensors are activated, so would an alarm condition. This increases the detectors stability and limits the risk of false alarms. In terms of changing conditions and swaying vegetation, the XDL12TT-AM features Anti-Sway Analytics. This advanced digital filter distinguishing between the movements of trees and plants from that of an intruder, to maintain optimum performance. The detector also boasts IP55 weatherproof rating, thick polycarbonate plastics and fully sealed optics for optimum external performance. It has even been moulded with a stabilising material to prevent discolouration over time! The XDL12TT-WE also features Anti-Interference Technology to prevent intruders from bypassing detection. This consists of Anti-Masking, which is a Grade 3 Patented Technology that protects against any attempt to mask any of the three sensors with cardboard, duct tape, sprays, lacquers or aluminium foil. It also consists of Anti-Blocking, which is a Grade 4 Technology that prevents the system from being armed if there is anything blocking the vision of any of the sensors. Therefore, to arm the system, whatever is blocking the detector from detecting needs to be removed first. Providing either volumetric or curtain coverage to suit the area that needs protecting, each lens can also be masked to restrict the coverage area. This is particularly useful in areas where busy roads can cause false alarms. The detector also boasts three different frequency bands to avoid any interference (cross-talk) that can occur when two or more detectors with the same frequency band are installed within close proximity of each other. This also allows multiple to be fitted, including the use of a fixed bracket, which enables two to be fitted back to back, providing 24m range with 180° volumetric coverage. Whatever the requirement, the XDL12TT-AM provides the ideal external security solution.
Pyronix, the intrusion specialist of the world-leading Hikvision group, is delighted to announce the launch of the Enforcer 64 total wireless security solution. Taking residential security to a new level, the Enforcer 64 is as quick-to-fit, easy-to-use and reliable as ever before, but features a new modern design and V12.5 firmware for Hik-Connect compatibility and dual path communication capability. “We are absolutely committed to driving market applications towards total solutions, with the upmost attention for innovation and quality,” Laurence Kenny, Pyronix Marketing Manager, comments. He continues: “With the Enforcer 64 we have delivered this in abundance with a complete solution that fuses security, video and lifestyle enhancements, with greater communication contingency and reassurance.” Pyronix first introduced the Enforcer wireless control panel in 2012. Since then it has consistently won multiple coveted industry awards, due to the company’s commitment to continuous improvement and innovative technological advancements by its dedicated R&D team. These developments have culminated in the Enforcer 64, which comes with heightened capabilities to enable security and monitoring in one solution. The Enforcer 64 utilises Pyronix award-winning two-way wireless technology, which is now expandable to 64 wireless inputs thanks to V12.5 firmware; double the number of the previous Enforcer solution. This makes adding wireless outdoor XD detectors, indoor KX detectors, sounders, keypads or safety devices easy, to suit any installation preference, without having to compromise. “The Pyronix Enforcer is our premier wireless solution for professional security installers and integrators, utilising the award-winning features it is renowned for within the security industry as the foundation for further development,” Laurence comments. He continues: “We have further developed it to be expandable to 64 wireless inputs, delivering greater installation capability whilst fusing it with Hikvision’s extensive range of video equipment, iVMS via Hik-Connect for seamless functionality; all of which combine to provide a total solution.” The panel is certified to Grade 2 and perfectly suited for residential and small to medium sized commercial applications. It also delivers for multiple installation preferences, with complete compatibility with the whole range of communication modules. The solution also boasts hybrid capabilities, with the ability to add any of the complete range of wireless and wired peripherals, alongside the ability to add up to 30 automation outputs. The Enforcer 64 fuses intrusion and video to bring together intrusion and video on one platform for enhanced customer value and upsell opportunities.
The Avigilon Presence Detector (APD) is a discrete impulse radar device that combines self-learning analytics with impulse radar technology to accurately detect the presence of a person even if they have stopped moving or are hidden. The device scans, learns, and continuously adapts to its environment, helping to reduce false positive events. Designed for indoor locations such as ATM rooms and other closed indoor vestibules within banks, pharmacies, health care facilities and retail stores, the APD can accurately detect a person’s presence through blankets, cardboard, wood and drywall. When integrated with Avigilon Control Center video management software, the sensor is designed to alert operators of security events while still maintaining privacy.
As the intruder market increasingly converges, with products and solutions entering from various rival markets, the time to integrate and evolve is now. There has been a rapid increase in end-user targeting, with solutions that deliver more than just security, but lifestyle solutions, including remote video monitoring, automation capabilities and more. This added value makes a system a desired enhancement to day-to-day life, rather than simply a grudge purchase to deter or alert of intrusion. It’s time to advance into new market applications and grow your business, by offering it all, with the totally integrated Enforcer V12 and Hik-Connect smart device application. With professional security integrity in mind, Hik-Connect is a user-friendly smart device application that brings together Pyronix multi-award-winning intruder security systems and technologies, with Hikvision’s world-leading video surveillance technologies and innovation. This seamless synergy enables you to deliver fully integrated and secure systems that are easy-to-install, flexible, extensive and meet your end users’ needs and desires. Thanks to seamless Hik-Connect integration, you can offer the ability to arm and disarm, check the status of any detector or sensor on the system and control any automation outputs, as well as access complete video monitoring of the property from anywhere, thanks to compatibility with any Hikvision video device. Available on Android and iOS, your end users can check any events, monitor when their children have arrived home safe from school, see what pets are getting up to, monitor outbuildings or even answer their front door or respond to deliveries with mic-enabled cameras, as well as see all the push notifications they have received - all from the palm of their hand. Should an event occur on the system, they can also simply and easily switch between their control panel and cameras for quick video verification. This simple switching also allows for easy multi-site monitoring, access to camera recordings and previews of live-streams. Deliver a security and video monitoring centre in the palm of the end user’s hand for any residential or commercial purpose. Hik-Connect is compatible with app-enabled Pyronix Grade 2 and Grade 3 security systems; offering outstanding usability and flexibility that is simple to install and easy to use. It’s time to advance. It’s time to integrate.
One of the main advantages of Software-as-a-Service solutions is interconnectivity. The cloud allows us to work in a completely different way than was possible before. In the past, an installer would have to get in their van and make a site visit to investigate any complaints or issues from their customer. Now, this can all be done remotely through SaaS-solutions like Vanderbilt’s SPC Connect, changing the entire service interaction quite dramatically. Vanderbilt wants to continue that evolution. Customers now expect very high levels of service from installers. SaaS-solutions are the perfect enabler to achieve this. With SPC Connect, Vanderbilt is delivering an ecosystem that will allow installers to have a better communication environment with their customers. The latest service release of SPC Connect brings installers closer to their customers by creating a platform where they can communicate more freely with each other. This ability to have more open communication between installer and end user, in a secure mechanism such as SPC Connect, will have a significant impact on increasing the level of service for all parties. Customer notifications Installers can communicate through the SPC Connect network directly to their customers. This feature allows installers to create a message that will appear directly in the user’s app and in their email. The messaging editor provides editing capabilities and the inclusion of links. The installer can also download the list of all customers interested in their message. User restrictions This enhancement delivers the security company greater control of the level of service they wish to offer through SPC Connect. The function allows the security company to define what operations are permitted by a user such as: Blocking Email; Blocking Push Notification; Blocking Alarm Verification; Blocking Mobile App; and Blocking Verification Web. Alarm verification via mobile devices If an SPC panel is part of an SPC Connect installer account, then a new feature will activate on the user device that will allow the user to view verification data. If the SPC panel is not part of a company, or the company has chosen to block this feature, then the users of that panel will not see any change. When this enhancement is enabled, when an alarm occurs that has verification, the user will be able to view the data and talk and listen live to site.
The BX Shield is a series of curtain outdoor motion sensors with up to 12m detection range on each side. Ideal for the detection of people in the immediate boundary of your home or office building, the outdoor detectors feature four PIRs, two on each side. The left and right detection area can be set up completely independently from each other. The BXS-RAM is the wireless bi-colour model with anti-masking. Independent left/right motion detection The outdoor motion sensor’s detection range, sensibility and alarm output can be set independently on the left and the right. The detection distance can easily be set at 2.5m, 3.5m, 6m, 8.5m to 12m on each side, and the sensitivity can be set from low to extremely high, detecting as small a difference in temperature as 1 degree Celsius. The BX Shield can be easily connected to a fixed dome CCTV camera to send a visual alarm when people enter the immediate boundary of the premises. Versatile design The BX Shield curtain sensor has been designed with the user in mind. A 90-degree unlocking system allows easy access to the settings area, while a spirit level helps to fix the sensor on straight. Black and silver face covers are available, enabling the outdoor curtain sensor to blend into its environment. Four PIRs in one sensor Why two PIR in each side? - To offer the best performance needed in an outdoor environment. On each side, the BX Shield motion sensor features two passive infrared beams; one pointing towards the floor and one pointing away from the sensor. Both beams need to trigger to confirm the detection. This system will ignore small to medium-sized animals such as dogs and detect only people. Applications Buildings Perimeters Approach House Key features Wireless curtain PIR up to 12m per side with anti-masking Completely independent detection setting Versatile and easy-to-install design Not affected by environment or small animals Connect to new or existing wireless alarm panel The BXS-RAM is a battery-powered sensor (no cabling requested) in which most wireless transmitters available in the market can be fitted. This enables the sensor to connect to an existing or new wireless alarm panel. The anti-masking function ensures that if the alarm panel will be notified if someone has sprayed, covered the sensor or changed its position.
Exhibiting at Security Essen, Hall 5, Booth B48. Version 8.0 of long-range award-winning LiDAR – the REDSCAN RLS-3060 series and its configuration software REDSCAN Manager are both available. The new firmware enables additional detection modes including loitering detection, day/night pattern to the 30m radius RLS-3060L, while it allows the high end model to extend its detection area to 50m radius. The RLS-3060L will offer more flexibility in managing dry contacts with the option to switch from normally open (N.O.) to normally closed (N.C.). The RLS-3060L model ver. 8.0 features more detection zones and detection modes as well as greater flexibility with settings. The standard 2D LiDAR provides 30m radius detection range with 4 detection zones when used in analogue configuration and 8 zones in IP configuration. Loitering and selectable pattern modes are now available. Alarm duration and detection time settings are also more adjustable.
Version 8.0 of long-range award-winning LiDAR – the REDSCAN RLS-3060 series and its configuration software REDSCAN Manager are both now available. The laser sensor with the new firmware version, together with the new configuration software provide a number of new features for both the standard model, RLS-3060L, and the high-end model, RLS-3060SH. The RLS-3060SH will offer more flexibility in managing dry contacts with the option to switch from normally open (N.O.) to normally closed (N.C.). The RLS-3060-SH provides additional detection modes to the L model, such as indoor ceiling protection and vehicle detection mode, and has one major new feature – an extended detection area between 30 and 50m. When used in horizontal detection it creates a pre-warning zone from 30 to 50m radius that is able to detect larger objects such as vehicles. In vertical mode when mounted at 3m off the ground, it can detect a standing or squatting person over 100m making it ideal to pick up intruders, a long wall or fence.
Exhibiting at Security Essen, Hall 6, Booth 6D90. Wireless technology is coming of age, with two-way communication capabilities now cementing wireless’ reliability. Vanderbilt’s SPC Wireless range includes detectors, panic buttons, fobs, and a transceiver, and has a number of benefits intended to make installers’ day-to-day work life easier. The SPC wireless range can extend to 500 meters, proving a more cost effective alternative than having to wire an entire building with cable. This range of 500 meters also cuts down on install time, ultimately cutting down on an installer’s expenses. SPC Wireless devices use the industry-leading Energizer® lithium batteries, meaning an extended battery life of five years. This means installers don’t have to go to site as often to keep changing out batteries, freeing up time for more urgent tasks. Settings for the SPC Wireless range are all configurable over the air. Again, this reduces the need for time-consuming site visits. Most other products require the physical need to flick dipswitches to change commands but Vanderbilt’s SPC Wireless is aimed at convenience first. All-in-all, installs for SPC Wireless are designed to be hassle-free. You just put up the control panel, wire the mains to it, place the wireless detector in position, and you’re good to go. In contrast, a wired solution can take, at a minimum, a day’s work fitting cable. By reducing time on site, Vanderbilt’s SPC Wireless can enable installers to get more work done elsewhere, essentially meaning more profits from more jobs.
Strong wireless signalling, multi-award-winning Enforcer two-way wireless technology and a whole host of intelligent reliability, security and detection features have all gone into the XDL12TT-WE. The first low-mount wireless outdoor detector of the Pyronix range combines multi-award-winning Enforcer two-way wireless technology with dependable external detection protocols, including: Dual-Vision Pet Immune, Tri-Signal Detection Logic and Gaussian Frequency Modulation (GFM), to deliver a highly dependable wireless external detector. IP55 weatherproof rated and consisting of two independent passive infrared (PIR) sensors and one microwave (MW) sensor in one common housing, its Tri-Technology (TT) delivers advanced outdoor protection. This is because, to identify the presence of an intruder, the XDL12TT-WE utilises Tri-Signal Detection Logic alongside TT, whereby all three sensors must be activated sequentially in quick succession to create an alarm. This heightens the detector’s immunity to false alarms and ensures optimum detection performance in external conditions. Along with Tri-Signal Detection Logic and TT, Pyronix has also pre-empted potential false alarm issues from the presence of pets or swaying vegetation, by including Dual-Vision Pet Immune and Anti-Sway Analytics features. Dual-Vision Pet Immune of the XDL12TT-WE consists of its two PIRs having a dedicated volumetric field of view, with the top PIR detecting outwards and up, while the bottom PIR detects outwards and down, without either crossing the central horizontal plane between them. This setup of non-overlapping PIR sensors alongside Tri-Signal Detection Logic, delivers highly secure sequential detection and increases its tolerance to pet immunity. Anti-Sway Analytics digitally filters the environment to distinguish between the movement of trees and plants from the movements of an intruder, so that false alarm activations are kept to an absolute minimum. These external detection protocols then benefit from the advantages of Enforcer two-way wireless technology, with full supervision, anti-jamming and 128-bit wireless protocol encryption, to maximise the new XDL12TT-WE’s reliability; ensuring signals transmitted by the system are protected and any code-grabbing is prevented. Two-way wireless also brings with it a whole host of installation benefits, without the invasive nature of fitting wired peripherals. This increases the efficiency of the installation for our customers, while providing a steadfast detector for end-users. In terms of the wireless signal, the XDL12TT-WE’s high sensitivity receiver is capable of a wireless signal range of up to 1.6km in open space, which reduces the need for repeaters and therefore reduces the installation cost. In addition, the high-sensitivity antenna of the XDL12TT-WE ensures that the signals being transmitted and received are as strong as possible, by utilising GFM to spread the signal, while reducing unwanted noise and harmonics. This enables the outdoor detector to meet stringent European, ETSI and other worldwide standards. When it comes to wireless outdoor security, why not deliver the XDL12TT-WE?
The CO8M is a Carbon Monoxide (CO) alarm device designed to identify dangerous levels of Carbon Monoxide and present an audible alarm on detection. This fully wireless device is fitted with a memory feature which will record all detections, alerting home owners to potentially dangerous events which have occurred whilst the home is unoccupied. The CO8M uses a proven electrochemical sensor which has been individually calibrated and tested in Carbon Monoxide (CO) gas to ensure accuracy. When dangerous levels of Carbon Monoxide are detected, the siren will sound and a red LED will flash to indicate an alarm status. The front panel is fitted with LED lights to indicate alarm, operation, fault, test and diagnostic conditions. The aesthetically pleasing design means this will not look out of place mounted on either the wall or ceiling of any property. The CO8M is fully compatible with all Honeywell Galaxy intruder control panels, (G2, Galaxy Flex and Dimension), and can also be used with the Domonial panel. For more information regarding the CO8M or any of our Intruder products, please visit www.honeywell.com/security/uk.Add to Compare
Browse Intruder Warning Devices
Intruder warning device products updated recently
As anyone who has ever flown on a commercial airline since 2001 knows, security measures at airports are well enforced and the emphasis on traveller safety is all around the airport and its grounds. Mass transportation, meanwhile, presents a special but not any less significant challenge when it comes to determining security issues. These facilities need to develop the means to protect a constantly changing and large population of passengers. And unlike airports these facilities often have hundreds of points of entry and exit on multiple modes—buses, subways, light rail, commuter trains, even ferries. About 2 million Americans will use the nation’s airways on a given work day, while 35 million people will board some form of public transportation. In fact, statistics have shown that nearly 11 billion trips are taken on public transportation every year. In some large metropolitan areas in North America where mass transit is well established, more than 20 percent of the area’s inhabitants get around via public transportation.About 2 million Americans will use the nation’s airways on a given work day, while 35 million people will board some form of public transportation Solving mass transit security For transportation officials and their security providers, solving the mass transit security issue begins with determining the key concerns and then creating the proper responses via security systems, policies and procedures to mitigate the risks. Although vandalism and graffiti are very visible signs of criminal behaviour in mass transit settings such as bus stops and subway stations, this is not where transportation officials typically focus their energy. Fences and gates can secure out-of-service buses and train cars, as can remote surveillance methods to keep such vandalism at a minimum. Instead, it is the day-to-day safety and security of transit riders and employees that should become the highest priority. This begins with creating the safest environment possible that is highlighted with appropriate signage and, when necessary, audible warnings, and supporting that with technology, such as surveillance cameras, that will document what has happened if an incident occurs.Analytics can also be useful in alerting security about other suspicious behaviours at a transit stop, such as an untended bag or package Crime prevention in transportation Analytics can also be useful in alerting security about other suspicious behaviours at a transit stop, such as an untended bag or package Incidents of concern within a transit setting can take several forms, ranging from legitimate accidents or crimes to false claims such as faked fall down the stairs to potential and actual suicides. Bus and subway stations also have become magnets for homeless people who may put themselves and others in harm’s way by trying to access less secure public areas within a station as temporary shelters. If someone is injured on a subway platform and the transit provider is held liable, it could be on the hook for hundreds of thousands, if not millions of dollars. Suicides are a major concern for operators, with personnel now being trained to look for individuals who seem distressed, are loitering in the area or are intentionally putting themselves in a dangerous situation, such as standing too close to the edge of a platform. The deployment of video analytics, which can be programmed to send alerts when certain pre-set actions occur, can help determine when such dangerous behaviours come into play. Analytics can also be useful in alerting security about other suspicious behaviours at a transit stop, such as an untended bag or package or a person going into a restricted area. Whether it is on the bus, train or ferry or at the stops themselves, cameras and intuitive video management systems are the key to both active and forensic transit security. Some cities use buses that are up to 60 feet long and those can be equipped with up to a dozen cameras Train security and safety By using the proper cameras and recording systems in a transit environment, quick-acting personnel can locate a person of interest who boarded a train at one station, follow him during his trip and produce a crisp, clear identifiable image at the end. Those setting up the system thus should keep in mind proper camera positioning, resolution and motion-based changes to framerates or other compression settings. A typical 30-foot bus often has six cameras—one each at the front and middle doors, two more within the bus and then one looking forward and another looking behind the bus. The latter two are important in the event of accidents to verify liability. Some cities use buses that are up to 60 feet long and those can be equipped with up to a dozen cameras.Train stations often deploy high-definition cameras to better support facial recognition software to get that actionable image Train cars are similarly equipped with two to four cameras to view activity down the centre aisle. Within the stations themselves, there can be from 15 to 30 or more cameras capturing wide-angle shots. Train stations, which have a restricted point of egress, often deploy high-definition cameras to better support facial recognition software to get that actionable image. Installing the right technology for the solution Although bandwidth and storage can be a concern, with motion-based recording, the resolution can be bumped up during event, resulting in a 1-megapixel stream jumping to 4 or even 8mbps when needed. By changing the resolution on demand, end users can cut their storage needs significantly. Transportation settings often rely on the same technology used in other security installations, primarily mini dome cameras, although there are some mini transit domes built specifically for the environment with the proper aesthetics. Because of vandalism threats, transit typically avoids pendant mounts, which can be more easily grabbed and damaged. Temperature ratings for cameras also come into play in cold climates with cameras often getting outdoor exposure.Today’s new buses and trains are constructed with the cameras onboard and newer stations also take security into consideration at the earliest design stage As trains and buses move along their routes, especially those that service outlying areas, Internet connectivity becomes an issue as well. Because it may be difficult for video to be sent in transit, security bus barns are equipped with Wi-Fi so video from onboard cameras can be downloaded at the end of the day. And the use of hardened recorders at the stations allows security personnel to retrieve recorded video. Transit security with modern technology Today’s new buses and trains are constructed with the cameras onboard and newer stations also take security into consideration at the earliest design stage. Older infrastructure from long-standing subway and bus terminals can prove to be a challenge when adding security, but these issues aren’t insurmountable. Often the solution is to add more cameras to cover the same square footage because of less-than-ideal sight lines and to place conduit wherever it works best, which may mean positioning it under platforms or in other out-of-the-way places within older stations. Looking ahead, transit security will continue to evolve, not only as new stations and modes of transportation are added to the system, but in terms of communicating with commuters. People can expect to get mass notification alerts on their mobile devices, and those same devices can provide vital data to transportation entities to better develop their overall systems.
In the state of the residential security market today, we see many who are offering home security packages that rely on numerous sensors and multiple devices to provide a comprehensive coverage of the home and provide peace of mind. Each individual sensor or device within the package provides a specific functionality, and the user finds himself burdened by an overwhelming amount of sensors and devices. This overload is intensified by the penetration of additional IoT and smart devices into the home, such as pet-cams or smart speakers that add to the burden of installation and maintenance. In addition, we are witnessing the rise in popularity of DIY security devices, indicating that users are looking for models and technologies that provide both contract flexibility and simplicity of use. The past years have seen major advancements in radar technology, which have brought the formerly military technology into the consumer space. Radars provide interesting prospects for home security and smart homes due to several inherent characteristics which give it an advantage over existing technologies. The resolution of an advanced radar sensor enables not only presence detection, but also provides advanced features for security, automation and well-being Advanced security and automation features Of primary importance, a consumer designed radar sensor provides the user with full privacy, but the use of radar is also beneficial because it is indifferent to environmental, temperature and lighting conditions. In addition, radar signals (at certain frequencies) are capable of penetrating through almost any type of material, enabling concealed installation, robust monitoring in cluttered spaces and even the coverage of several separate rooms with only one device. In terms of capabilities, simple time of flight 2-antenna radar sensors, which have been around for a while, do not provide much additional value in comparison to existing solutions and are not necessarily competitive in terms of pricing. However, the new generation of radar sensors are also opening up new capabilities previously achieved with optics only. Today, the resolution of an advanced radar sensor is high enough to enable not only presence detection, but also to provide advanced features for security, automation and well-being, all in one. Imagine for example, that the security sensor installed in your elderly parent’s home could also detect a fall having occurred, monitor the breathing of a baby or even leaks in your wall. Due to the unique field of view that radar provides as well as the multi-functional potential, this technology will be the key to the awaited convergence of smart home functionalities and minimisation of home devices. The security sensor installed in your elderly parent’s home could also detect a fall having occurred Secret of the consumer radar A radar sensor’s accuracy and its ability to support wide functionality and applications is determined initially by its resolution, which is based on two key factors: bandwidth and number of channels. The wider the bandwidth and the more channels the radar supports, the more accurate the data received. Imagine the difference between a 1990s television model and a 4K 2018 television model - As the resolution is ever improving, the sharper and more detailed is the image. When looking at the short-range radar sensor market, prominent companies such as Texas Instruments and NXP are offering radar-on-chip solutions supporting 2\3 transmitters (Tx) and 3\4 receivers (Rx), mainly utilising frequency bands of 77-81GHz, as they target mostly automotive and autonomous driving applications. Another company that develops such radar-on-chip solution is Vayyar Imaging, an Israeli start-up, founded in 2011, that developed a radar sensor for 3D imaging. Vayyar Imaging directly targets the smart home and security markets with its radar-on-chip, developing modules and products for intruder detection, automation and elderly care (fall detection). Providing not only chips, but complete systems, the new model makes radar technology highly available and accessible. The radar-on-chip technology opens the door to installation of security and well-being devices in locations where privacy or environmental conditions pose an issue Radar-on-chip solution The radar-on-chip solution supports 72 full transceivers, an integrated DSP and radar bands between 3-81GHz. The resolution provided by this type of specification is high enough to provide subtle information about people’s real time location posture (lying down\falling\sitting\walking), and breathing, and enables to classify pets from humans, but it is low enough as to not compromise privacy. This type of technology opens the door to installation of security and well-being devices in locations where privacy or environmental conditions pose an issue, such as in bathrooms or heavily lit environments. Moreover, utilisation of this technology allows to dramatically minimise the numbers of sensors installed in the home, as it provides full home coverage with just one or two sensors and enables using the same HW to support additional capabilities such as breath monitoring, fall detection and highly accurate automation. Using AI and machine learning, the data derived by these sensors can be leveraged to provide smarter, verified alerts on the one hand and whole new insights on the on the other. The sensor can be tuned to learn the location of the house entrances or boundaries, where the inhabitants are expected to be at night, or where they should be expected to enter from into the home, adding new logics to the traditional yes\no decision making. Home security is widely regarded as a necessity, provides peace of mind to people and is integral to people's day to day lives Additional smart home services Among the evolving home technology verticals, security is by far the most relevant and integral to people’s day to day lives. Home security is widely regarded as a necessity and provides peace of mind to people. Being a legacy industry with many well-known and well-trusted brands, security players are well positioned to introduce new technology into the home and have the ability and credibility to expand their offerings to additional smart home services by utilising existing infrastructure and channels. With technology giants entering the security arena through the smart home door the DIY security solution market expected to explode with a CAGR of 22.4% (according to a report by Persistence Market Research). Now that new pricing and service models offer minimal commitment, traditional security players will need to step up. Security companies will need to explore new technologies and expand their offering if they intend to stay relevant and competitive in a market trending on functionality converge and minimisation of maintenance and installation costs.
With the ever-growing availability of video data thanks to the low cost of high-resolution video cameras and storage, artificial intelligence (AI) and deep learning analytics now have become a necessity for the physical security industry, including access control and intrusion detection. Minimising human error and false positives are the key motivations for applying AI technologies in the security industry. What is artificial intelligence? Artificial intelligence is the ability of machines to learn from experience using a multi-layer neural network, which mimics the human brain, in order to recognise items and patterns and make decisions without human interference. The human brain is estimated to have 86 billion neurons; in comparison, the newest Nvidia GPU Volta has 21 billion transistors (the equivalence of a neuron), which offers the performance of hundreds of CPUs for deep learning.AI can learn continuously 24 hours per day every day, constantly acquiring, retaining and improving its knowledge In addition, unlike humans, AI can learn continuously 24 hours per day every day, constantly acquiring, retaining and improving its knowledge. With such enormous processing power, machines using Nvidia GPU and similar chips can now distinguish faces, animals, vehicles, languages, parts of speech, etc. Depending on the required complexity, level of details, acceptable error margin, and learning data quality, AI can learn new objects within as fast as a few seconds using Spiking Neural Network (SNN) to a few weeks using Convolution Neural Network (CNN). While both SNN and CNN offer advantages and drawbacks, they outperform tradition security systems without AI in terms of efficiency and accuracy. According to the research reports of MarketsandMarkets, the market size of perimeter intrusion detection systems is projected to increase from 4.12 billion USD in 2016 to 5.82 billion USD in 2021 at a Compound Annual Growth Rate (CAGR) of 7.1%. Meanwhile, the predicted market of AI in security (both cyber security and physical security) will grow from 3.92 billion USD in 2017 to 34.81 billion USD by 2025, i.e., with an impressive CAGR of 31.38%. Legacy perimeter intrusion detection systems Legacy perimeter intrusion detection systems (PIDSs) are typically set up with the following considerations: Geographical conditions: landscape, flora, fauna, climate (sunrise, sunset, weather conditions, etc.), whether there are undulations in the terrain that would block the field of view of cameras Presence or lack of other layers of physical protection or barriers Integration with other systems in the security network: camera, storage, other defensive lines (door, lock, alarm, etc.) Types of alarm triggers and responses System complexity: intrusion detection with various types of sensors, e.g., microwave sensors, radar sensors, vibration sensors, acoustic sensors, etc. Length of deployment Local regulations: privacy protection, whether the cameras/sensors must be visible/hidden/buried, etc., electromagnetic interferences that may affect other systems such as oil rigs or power plants Human involvement: on-site personnel arrangement, human monitoring, human action in response to alarms AI object detection can easily distinguish different types of people and objects Pain points and benefits of AI The conditions listed above correspond to certain requirements of an intrusion detection systems: minimal false alarm, easy setup and maintenance, easy integration, and stable performance.AI by nature is designed to learn, adapt itself and evolve to work in multiple conditions: it should be integrated with existing video recording systems Minimal false alarms: False alarms lead to increased cost and inefficiency but are the main problem of PIDSs without AI technology, where animals, trees, shadows, and weather conditions may trigger the sensors. AI object detection can easily distinguish different types of people and objects, e.g., in a region set up to detect people, a car driving by, a cat walking by, or a person’s shadow will not trigger the alarm. Therefore, the amount of false alarms can be reduced by 70% to orders of magnitude. Easy setup and maintenance: Legacy PIDSs without AI must account for terrain, line of sight of cameras, sensor locations; any changes to the system would require manual effort to recalculate such factors and may disturb other components in the system. In contrast, AI PIDSs enable the system administrator to access the entire system or individual cameras from the control room, configure the region and object of interest in the field of view of cameras within minutes, and adjust with ease as often as necessary. Computing knowledge and even specific security training are not required to set up a secured PIDS with AI because AI PIDS is designed to relieve humans from knowing the inner working of machines. Easy integration with complementary technologies: Legacy PIDS without AI relies on physical technology, which are often proprietary and require complete overhaul of systems to function smoothly. On the other hand, AI by nature is designed to learn, adapt itself and evolve to work in multiple conditions, so AI PIDS is easily integrated with existing video recording (camera) and storage (NVR) systems. AI also eliminates the need for physical wireless or fiber-based sensors; instead, it functions based on the videos captured by cameras. Furthermore, AI enables easy and instantaneous combinations of multiple layers of defense, e.g., automatic triggering of door lock, camera movement focusing and access control as soon as a specified object is detected in the region of interest, all set up with a click of a button. Stable performance and durability: Legacy PIDSs without AI requires complicated setup with multiple components in order to increase detection accuracy. More components mean a higher probability of malfunction in the system, including exposure to damages (e.g., sensors can be destroyed) and delay in detection, while human monitoring is inconsistent due to human fatigue (studies have shown that a person can concentrate in mundane tasks for only up to 20 minutes, and the attention span decreases even more rapidly when humans are faced with multiple items at once, e.g., multiple camera monitoring screens). AI significantly reduces, if not completely eliminates the need for human involvement in the intrusion detection system once it is set up. In addition, AI reduces the risk of system malfunction by simplifying the hardware sensors needed. Minimising human error and false positives are the key motivations for applying AI technologies in the security industry Additional benefits of AI in intrusion detection Artificial Intelligence is undeniably reshaping every business and weaving into every aspect of daily lifeMaximal detection capability: The most advanced AI intrusion detection system today provides an all-in-one solution to distinguish any combination of alarm-triggering criteria beyond perimeter protection. Using AI, the system administrator can configure as many zones with different settings and object of interests as necessary, which include detections for specific colors or attributes (e.g., person not wearing the required uniform or carrying food/drink), numbers and dwell time (e.g., group of more than 5 people loitering), or movements (e.g., cars moving faster than the speed limit). In addition, AI can accurately pinpoint the location of event occurrence by displaying the camera that records the event in near real time, i.e., with few-second delays. Lower security operation cost: By minimising the number of false positives and human involvement while maximising ease of use and stability, AI intrusion detection systems significantly decrease the total cost of ownership. Companies can reduce the large security personnel overhead and cost of complicated and expensive legacy PIDSs systems. McKinsey Global report in June 2017 shows that proactive AI adopters can realize up to 15% increase in profit margin across various industries. Artificial Intelligence is undeniably reshaping every business and weaving into every aspect of daily life. In security, legacy systems are giving way to AI-based systems, and the first enterprises to adopt AI-based systems will soon, if not immediately, benefit from such investment. By Paul Sun, CEO of IronYun, and Mai Truong, Marketing Manager of IronYun
Is your access control as effective as you think?Download
How to get buy-in from IT departments on IP video installationsDownload
The role of IT in physical access controlDownload
- Knightscope to beta test suite of developing technologies at Clovis Unified School District
- CriticalArc’s SafeZone indoor positioning solution installed at Texas A&M University
- ASSA ABLOY’s CLIQ electronic locking system secures entrances for Creval bank in Italy
- DoubleTree by Hilton in Boston integrates fire audio solution from Advanced Fire Systems